Safety Instructions - Conrad RSLT2 Mode D'emploi

O P E R A T I N G I N S T R U C T I O N S
2-Channel Wireless Wall Switch
RSLT2
Item-No. 64 64 67
Intended Use
This 2-channel wireless wall switch is designed to turn on and off two appropriate receivers (e.g.
wireless power socket, wireless outdoor socket, wireless inbuilt switch etc.) In addition, this
2-channel wireless wall switch has a dimming function (for example, to control a wireless plug-
in dimmer, wireless inbuilt dimmer etc.).
For each control channel, a maximum of 10 receivers can be programmed.
The 2-channel wireless wall switch is only intended for use in dry indoor locations.
The wireless wall switch is powered by a 12 V battery (type: 23A).
All the safety and operating instructions in this manual must be followed carefully. These
instructions not only protect the device but, in particular, your health. Please read the entire
operating manual before using the product.
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner.
All rights reserved.

Safety Instructions

The warranty will be void in the event of damage caused by failure to observe
these safety instructions. We do not assume any liability for any consequential
damage!
We do not accept liability for damage to property or personal injury caused
by improper handling or non-compliance with the safety instructions. The
warranty will be void in such cases.
• The unauthorized opening, conversion and/or modification of this product is not
permitted because of safety and approval reasons (CE).
• Do not use this product in hospitals or medical institutions. Although the product
emits only relatively weak radio signals, these may lead to the malfunction of life-
support systems. The same may be the case in other areas.
• The wireless wall switch is powered by a 12 V battery (type: 23A).
• The product is not a toy and must be kept out of the reach of children. Therefore,
be especially careful when children are around.
• The wireless wall switch is only suitable for use in dry indoor locations.
• Do not leave packing materials unattended. They may become dangerous
playthings for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
Battery notes
• Keep batteries out of the reach of children.
• Please pay attention to the correct polarity (plus/+ and minus/-) when inserting the battery.
• Do not leave batteries lying around in the open; there is a risk of them being swallowed by chil-
dren or domestic animals. If swallowed, consult a doctor immediately.
• Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suitable
protective gloves.
• Make sure that the battery is neither short-circuited nor thrown into a fire. There is a risk of
explosion!
• Do not recharge normal batteries. There is a risk of explosion! Only charge rechargeable
batteries that are intended for this purpose; use a suitable battery charger.
• If it is not to be used for a while (e.g. storage), remove the battery. Old batteries may leak and
cause damage to the product, which will lead to the loss of the warranty/guarantee.
• For the environmentally friendly disposal of batteries and rechargeable batteries, please read
the chapter "Disposal".
Installation and Connection
www.conrad.com
Version 09/09
• Carefully lift the front cover of the wireless wall switch (e.g.
°
with a screw driver) and remove it (see picture on the
right).
• Remove the mounting plate. The mounting plate for the
wireless wall switch is fixed to the electronic part of the
wireless wall switch with 4 clamps (see picture on the
right).
• The mounting plate has two mounting holes (see the
picture on the right). Remove the mounting plate and mark
the mounting holes on the wall.
• Drill the holes.
• Attach the mounting plate to the wall, using suitable
mounting material.
• Attach the electronic part of the wireless wall switch to the
mounting plate.
• Insert a 12V-battery (type: 23A) in the battery compart-
ment of the wireless wall switch, paying attention to the
correct polarity.
• Attach the front plate to the wireless wall switch.
Programming a receiver for the wireless wall switch
For each control channel, a maximum of 10 receivers can be programmed.
• Set the receiver to the programming mode. Please follow these operating instructions when so
doing.
• Press the desired „I" button on the wireless wall switch to which the receiver is to be pro-
grammed. The programming has been completed successfully.
Deleting programmed receivers from the wireless wall switch
• Press the buttons „I" and „O" on the wireless wall switch to which the receiver is programmed.
The LED on the receiver starts flashing.
• Now press the button „O" on the wireless wall switch. The LED on the receiver goes out. The
receiver has now been deleted from the wireless wall switch.
The wireless wall switch's dimmer function
• Turn on the dimmer, by briefly pressing the „I" button on the wireless wall switch once.
• Press the „I" button on the wall switch again. The dimmer function is activated.
• Press the „I" button on the wall switch again. The dimmer function is deactivated.
Start-up, Function Test
Commission the receiver in the correct way (follow the receiver's operating instructions).
By pressing the appropriate „I" or „O" button on the wireless wall switch, the receiver is turned
on or off.
Maintenance and Care
The product does not require any maintenance and should never be opened or disassembled
for any reason.
Only clean the product with a soft, clean, dry cloth. Never use aggressive cleaning agents or che-
mical solutions since these might damage the surface of the casing or impair the operation.
Handling
The wireless wall switch is only intended for use in dry indoor locations.
• The wireless wall switch is only intended for use in dry indoor locations.
• Avoid the following unfavourable environmental conditions at the installation
location or during transport:
- Humidity and damp may cause damage to the product
- Direct sunlight
- Extreme cold or heat
- Dust or flammable gases, fumes or solvents
- Strong vibrations
- Strong magnetic fields such as those found in the vicinity of machinery or loud-
speakers
• Ensure that the insulation for the entire product is neither damaged nor destroyed.
Never disassemble the product! There are no serviceable parts inside.