Parts List; Preparation - Foundations Child Craft F10391 Instructions De Montage

PARTS LIST

Part Number Quantity
Part Description
A. Dowel Pin 10mm x 40mm
11200323
B. Joint Connector Nut 1/4-20
11200077
C. Allen Head Bolt 80mm 1/4-20
11200389
D. Allen Head Bolt 14mm 1/4-20
11200388
E. Allen Head Bolt 55mm
11200089
F. Allen Wrench
11200070
G. Connector Nut
11200068
H. End Panel Footboard
22301038
I. Foot Post Left
22301048
J. Foot Post Right
22301049
K. Top Cap
22301052
L. Stretcher
22301046
M. Front Stationary Side
22301040
N. Back Stationary Side
22301041
O. End Panel Headboard
22301047
P. Head Post Left
22301050
Q. Head Post Right
22301051
R. Spring
11200333

PREPARATION

Carefully remove and lay out all hardware and parts.
Check quantities and match the parts list.
Construct Crib on an even flat floor.
Note: during the assembly process whenever
using screws or bolts, Check each with the parts list
by letter and size identification. Place each screw
or bolt on the diagram of the item which is sketched
actual size. Be sure to use the proper size specified
in the assembly directions. If any parts are missing
or broken or you need assistance with assembly
The Allen Head Bolts D have a friction enhancing
patch on the thread which may cause resistance
during tightening.
DO NOT return your product to the dealer.
Please identify the crib by the model number
identification stamped on the inside face of the
Stationary side assembly when you call or write to
Foundations®. Make note of all identification
numbers and include this information with your
request.
DO NOT Substitute Parts!
SUGGESTED TOOLS
#2 Medium Straight Screwdriver
B
A
4
18
8
C
8
14
2
4
E
D
1
1
1
2
G
1
F
1
1
1
1
1
1
Hardware Package
H
I J
M L
O
P
Q
Crib Parts
2
Construct End Panel Footboard assembly:
Align Foot Post Left I onto dowel on End Panel
Footboard H Top Rail and push together making
sure slotted hole is on the inside opposite the
Childcraft logo. Place Joint Connectors Nut B into
holes in the bottom of top and bottom rail of End
Panel Footboard H . Insert Allen Head Bolts C into
Foot Post and rotate Joint Connector Nuts to align
threads with bolts. Snug Bolts and Connectors with
Allen wrench .
Repeat procedure with Foot Post right J . Note Foot
Post Right J has no slotted holes.The (3) through
holes in the face have a counterbored (larger) entry
hole which will be located on the same face as the
childcraft logo
Insert Dowel Pins A into outer holes on top of End
Panel Footboard H . Place Top Cap K on top of
AB20047_G3
End Panel Footboard H and align with the Dowel
Pin. Insert Allen Head Bolts E into underside of top
of End Panel Footboard H then thread into metal
K
inserts in top cap K .
Tighten all bolts securely.
See figure 1.
Construct End Panel Headboard assembly:
Align Head Post Left P onto dowel on End Panel
N
Headboard O Top rail and push together making
sure slotted hole is on the inside.
Place Joint Connector Nuts B into holes in the
bottom of top and bottom rail of End Panel
Headboard O Insert Allen Head Bolts C into Head
Post and Rotate Joint Connectors Nuts to align
threads with bolts and snug with Allen wrench .
Repeat procedure with Head Post right Q . Note
Head Post Right Q has no slotted holes. The (3)
through holes in the face have a counterbored
(larger) entry hole which will be located on the
outside face (opposite face from slotted hole in
Head Post left P ).
R
Insert Dowel Pins A into outer holes on top of End
AB20047_G4
Panel headboard O .Place Top Cap K on top of
End Panel Headboard O and align with the Wooden
dowel Pin. Insert Allen Head Bolt E into underside
of top of End Panel Headboard H . Then thread into
metal inserts in top cap K .
Tighten all bolts securely.
See figure 2.
STEP 1
A
E
K
I
A
C
B
Figure 1
STEP 2
A
E
K
A
P
C
O
B
Figure 2
3
H
C
J
AB20047_G5
C
Q
AB20047_G6