Starting Up And Using The Machine; Tightening The Stirrer; Switching The Machine On And Off; Control Electronics - Protool MXP 1000 E EF Notice Originale

6 Starting up and using the
machine
Check that the information on the manufacturing
label complies with the actual power supply volt-
age.
Check that the plug type is the same as the socket
type.
6.1

Tightening the stirrer

(see Fig. [2])
Screw in the stirrer [2-4] with endpiece M14x2
(wrench size 22) by turning it to the right in the
adapter ErgoFix [2-1] (wrench size 19) and use
the wrench to tighten it.
Fasten the ErgoFix adapter to the stirrer bar, then
insert the assembled stirrer into the slot of the
spindle. To set-up the working height see chap-
ter 6.5.
6.2

Switching the machine on and off

► Always hold the machine with both hands.
Pressing the switch [1-3] puts the machine into
operation and taking your hand away from the
switch stops the machine from working.
Using the switch button to control the speed
(acceleration function switch)
You can use the switch [1-3] to change the level
of the speed until it reaches the speed range that
is set by the speed controller.
Continuous operation
By pressing the switch [1-3] as far as it goes and
pressing the locking switch button [1-4] at the
same time, you can activate continuous operation.
Press and release the switch button [1-3] again to
switch off continuous operation.
6.3

Control electronics

Limiting the starting current
The electronically-controlled soft start ensures that
the machine starts up smoothly.
At the same time, this also prevents the materi-
als to be stirred from spurting out of the mixing
container. Thanks to the low starting current of the
machine, a 10 A fuse is suffi cient.
Electronic speed preselection
You can use the speed controller [1-5] to set the
speed:
MXP 1000 EE F, MXP 1200 EE F
Level 1
Level 2
Level 3
12
360 Level 4
410 Level 5
470 Level 6
MXP 1002 EE F
1st speed
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
The speed depends on the stirrer rod that is used
and on the material that you want to process.
Overload protection
An electronic overload protection protects the mo-
tor from damage if there is an extreme overload.
In this case, the motor remains at a standstill and
only starts up again once the load has been re-
moved. To restart the machine, you must switch
it on again.
Constant Electronic function
The Constant Electronic function maintains an al-
most constant speed and load; this ensures that
the material is stirred evenly.
Temperature-dependent overload protection
(VALID for the type MXP 1002 E EF and
MXP 1200 E EF)
To protect the machine against overheating if you
are using it for an extremely prolonged period,
switch the safety electronics to the cooling mode
as soon as the critical temperature is reached. You
cannot load the machine and it runs at a reduced
speed. Approx. 2 minutes after cooling, the ma-
chine is again ready for use and fully able to take
loads.
Protection against re-starting
Prevents the uncontrolled starting of the device
after current supply cut off. For re-starting, the de-
vice must be fi rst switched off and again switched
on.
6.4

Speed selection switch

(VALID for the type MXP 1002 E EF)
You can use the speed selection switch [1-9] to
preselect two speed ranges:
1st speed
360 – 630 rpm
The gears can be switched when the machine is
running down, however not under full load.
520
6.5

ErgoFix interface

580
Height setting
630
The working height of the machine can be indi-
vidually adjusted to achieve an upright working
position.
- Push the casing of the ErgoFix adapter [1-7] in
the direction of the machine to move it as far
as it goes [1-7] and hold it tight.
2nd speed
360 Level 1
410 Level 2
470 Level 3
520 Level 4
580 Level 5
630 Level 6
2nd speed
580 – 1010 rpm
580
670
760
840
930
1010