Intended Use - Defort DFS-135N Mode D'emploi

English
Finishing sander

INTENDED USE

This tool is intended for dry sanding and fi nishing of
wood, painted surfaces, plastic and fi ller
TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1 On/Off switch
2 Switch locking button
SAFETY
WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock,
fi re and/or serious injury.
● Avoid damage that can be caused by screws, nails
and other elements in your workpiece; remove them
before you start working
● Always keep the cord away from moving parts of the
tool; direct the cord to the rear away from the tool
● When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
● Use completely unrolled and safe extension cords
with a capacity of 16Amps (U.K. 13Amps)
● In case of electrical or mechanical malfunction, im-
mediately switch off the tool and disconnect the plug
● SBM Group can assure fl awless functioning of the
tool only when original accessories are used
● This tool should not be used by people under the age
of 16 years
● The noise level when working can exceed 85 dB(A);
wear ear protection
● If the cord is damaged or cut through while working,
do not touch the cord, but immediately disconnect the
plug
● Never use tool when cord is damaged; have it re-
placed by a qualifi ed person
● Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
● This tool is not suitable for wet sanding
● Do not work materials containing asbestos (asbestos
is considered carcinogenic)
● When sanding metal, sparks are generated; do not
use dustbox and keep other persons and combustible
material from work area
● Do not touch the moving sanding sheet
● Do not continue to use worn, torn or heavily clogged
sanding sheets
● Wear protective gloves, safety glasses, close-fi tting
clothes and hair protection (for long hair)
1
2
● Take protective measures when during work dust
can develop that is harmful to one's health, combustible
or explosive (some dusts are considered carcinogenic);
wear a dust mask and work with dust/chip extraction
when connectable
● Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
● Do not connect the blue (= neutral) or brown (= live)
wire in the cord of this tool to the earth terminal of the
plug
● If for any reason the old plug is cut off the cord of
this tool, it must be disposed of safely and not left unat-
tended
● the dust suction requires the use of perforated sand-
ing sheets
● perforation in sanding sheet should correspond with
perforation in sanding foot
● replace worn sanding sheets in time
● always use the tool with the total sanding surface
covered with sanding paper
● before the sanding surface reaches the workpiece,
you should switch on the tool
● before switching off the tool, you should lift it from the
workpiece
● do not apply too much pressure on the tool; let the
sanding surface do the work for you
Your machine is double insulated in accord-
ance with EN 50144; therefore no earthwire is
required.
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.If the dirt does not come off use a soft
cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please
contact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of
the packaging materials can be recycled. Take these
materials to the appropriate recycling locations. Take
your unwanted machines to your local SBM Group
dealer. Here they will be disposed of in an environmen-
tally safe way.
4