Before Every Treatment - Tria 4X Mode D'emploi

NOTE: To prevent damage to your Tria Laser 4X,
use only the included Tria battery charger. If you
lose the charger, please contact Customer Service.
NOTE: You may charge the laser in Quiet mode
(charges without the sound of cooling fan), but
it will take longer. To change charging modes,
press the power button while charging.
TEST THE LASER ON A PATCH OF SKIN
Before your first full treatment on a new area
of your body, we recommend you test the
Tria Laser 4X on a patch of skin there and try
different energy levels.
1.
Prepare your skin and unlock the Tria Laser 4X
(see page 10). The Tria Laser 4X will be set
to Level 1 (low).
2. Place the treatment window flat against your
skin, and test one laser pulse.
3. If Level 1 was tolerable for you, then move to
another test area and increase to Level 2, testing
a patch at that level with one laser pulse. To adjust
the Tria Laser 4X setting up or down, press the
power button (see page 11).
4. If Level 2 was tolerable for you, change test
locations and increase by one level until you find
the highest setting that is still tolerable. Treating
at the highest level possible will maximise results.
5. Wait 24 hours and then examine the test areas.
If the skin appears normal, start your first treatment
at the highest level you are comfortable using.
Retest your skin if your skin tone changes
dramatically (due to tanning).
If you notice blistering, burns, changes in
your skin tone or any other side effects, or if
you are not sure about the outcome of the test,
DO NOT USE your Tria Laser 4X. Contact Customer
Service or your doctor.

BEFORE EVERY TREATMENT

PREPARE YOUR SKIN
1. Cleanse the treatment area, removing all
cosmetics, lotions and creams that may block
the laser light.
2. Shave the treatment area. This removes the
surface hair, which improves comfort and allows
the light to better reach the hair in the follicle.
3. Dry the treatment area.
Tria Beauty
EN
UNLOCK THE LASER
The Tria Laser 4X will lock when it's not in use.
To unlock the Tria Laser 4X, use the skin sensor,
which helps confirm that the Tria laser is safe
for your skin tone. To unlock:
1.
Unplug the Tria Laser 4X from the battery
charger and press the power button to turn
it on. The display will show the lock and skin
sensor icons.
2. Hold the skin sensor (red light at the base of
the Tria Laser 4X) against the skin in the area you
wish to treat. The skin sensor will automatically
sense and check your skin. If the Tria Laser 4X
is safe for your skin tone, the Tria Laser 4X will
emit a series of beeps and unlock.
1 2 3 4 5
10 11
3. If the lock icon is still visible and you do not
hear a series of beeps, then it may not be safe
for you to use the Tria Laser 4X. Or, you may be
using the skin sensor incorrectly and need to try
again. To try again, lift the skin sensor from your
skin and follow Steps 1 and 2 above. If you still
cannot unlock the Tria Laser 4X, please contact
Customer Service for assistance.
SET THE TREATMENT LEVEL
The Tria Laser 4X has different energy levels.
In a clinical study, higher levels were found to
be 2-3 times more effective. So for best results,
we recommend you use the highest setting
that you can tolerate.
When the Tria Laser 4X is on and unlocked, press
the power button to select your desired level.
Each time you press the power button, the level
will increase. Once the Tria Laser 4X is at the
maximum level, pressing the power button again
will return it to the lowest level.