Worx WG212E.1 Traduction Des Instructions Initiales page 9

OPERATING INSTRUCTIONS
WARNING! Do not use the product without
attaching the guard and front handle.
INTENDED USE
This machine is intended to be used domestically
for cutting and trimming hedges and bushes.
1. ASSEMBLY OF THE GUARD (See Fig. A)
Insert the Safety Guard(5) into the slot as illustrated
in Fig. A;
Use two screws to fix the guard securely.making
sure it is securely attached.
2. FRONT HANDLE ASSEMBLY
The Front Handle (4) must be assembled
before use:
1) Attach the Front Handle to the housing. Push
the small button (a) inside first. Make sure
the protruding marks on the Front Handle fit
perfectly into the matching indentation on the
housing. (See Fig. B & C)
2) Insert and tighten the 4 screws.
3) Check whether handle is firmly secured, if not
retighten the screws.
Make sure the handle is securely attached in
place.
3. MAINS SUPPLY CABLE STRAIN RELIEF
(See Fig. D)
An extension cord retainer is supplied to reduce
strain on the power cord. To use this feature, form a
loop at the end of the extension cable and bring this
through the opening at the bottom of the Extension
Cord Retainer, then wrap the end of the loop around
the hook and pull to tighten.
4. STARTING AND STOPPING (See Fig. E, F)
BEFORE STARTING YOUR HEDGE TRIMMER
Remove Blade Sheath (7).
TO START YOUR HEDGE TRIMMER
There are two switch levers fitted in your Hedge
trimmer (2&3).
Both switch levers need to be depressed for the
product to START. Depress and hold the Front
Switch Lever (3) and press the Rear Switch Lever (2)
(See Fig. E).
TO STOP YOUR HEDGE TRIMMER
Move Hedge trimmer away from cutting area before
stopping.
To STOP, release one of the switch levers (See Fig. F).
WARNING: If any parts are missing,
damaged or broken, do not operate your
Hedge trimmer until all damaged parts have
been replaced or repaired. Failure to do so could
result in serious personal injury. DO NOT USE
WITHOUT HANDLE AND GUARD.
5. HOW TO USE YOUR HEDGE TRIMMER
Inspect the area to be cut before each use, remove
objects which can be thrown or become entangled
in the cutting blades.
Hedge trimmer
Always hold the Hedge trimmer with both hands and
with the blade away from you before turning it on.
Always keep the power cord behind the Hedge
trimmer when in use. Do not place it over the
hedge that you are trimming where it may be
cut by the blade.
When trimming new growth, use a wide sweeping
action so that the stems are fed directly into the
blade.
Allow the cutting blades to reach full speed before
entering the material to be cut.
Always work going away from people and solid
objects such as walls, large stones, trees, vehicles
etc.
If the blade stalls, immediately stop the Hedge trimmer.
Disconnect the Hedge trimmer from the mains and
clear the jammed debris from the cutting blades.
Wear gloves when trimming thorny or prickly growth.
Move the Hedge trimmer to feed the branches
directly into the blade cutting edges.
Do not try to cut stems that are too large to feed
into the cutting blade.
TOP CUTTING (See Fig. G)
Use a wide sweeping motion. A slight downward tilt
of the cutting blades in the direction of motion gives
the best cutting results.
SIDE CUTTING (See Fig. H)
When trimming the sides of the hedge, begin at the
bottom and cut upwards, tapering the hedge inward
at the top. This shape will expose more of the
hedge, resulting in a more uniformed growth.
WARNING: Check extension cords before
each use. If damaged replace immediately.
Never use your tool with a damaged cord
since touching the damaged area could cause
electrical shock resulting in serious injury.
If the supply cord is damaged, it should be replaced
by a local approved Service Centre.
Take care not to expose this tool to rain.
MAINTENANCE
CLEANING
Disconnect from mains electrics supply. Using a soft
brush-remove debris from all air intakes and cutting
blade.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
Wipe over surface of your Hedge trimmer with a
dry cloth.
WARNING! Never use water for cleaning your
Hedge trimmer. Do not clean with chemicals,
including petrol, or solvents as this can damage
your hedge trimmer.
LUBRICATING THE CUTTING BLADE
For easier operation and longer life, lubricate the
cutting blades before and after each use. Before
lubricating, make sure your Hedge trimmer is
disconnected from the mains electricity supply.
Apply the oil so that it runs between the two blades
(See Fig. I).
9
EN