Samsung 6 Serie Mode D'emploi page 29

How to set up manually
To enter the Network settings into your TV, follow these
steps:
1. Follow Steps 1 through 6 in the "How to set up using
PBC (WPS)". (P. 27)
2. Press the ▼ button to select Internet Protocol Setup,
and then press ENTERE button. Press the ▲ or ▼
button to select Manual, and then press ENTERE
button.
3. Press the ▼ button to go to the first entry field (IP
Address).
4. Use the number buttons to enter numbers.
5. When done with each field, use the ► button to move
successively to the next field. You can also use the other
arrow buttons to move up, down, and back.
6. Enter the IP Address, Subnet Mask, and Gateway
values.
7. Press the ▲ or ▼ button to go to DNS.
8. Press the ▼ button to go to the first DNS entry field.
Enter the numbers as above.
9. When done, press the ▲ button to go to Select
a Network. Select your network, and then press
ENTERE button.
10. Go to Step 4 in the "How to set up automatically" (P. 27),
and follow the directions from that point on.
Network Setup
(SWL (Samsung Wireless Link))
This function lets you connect a Samsung device that
supports the PBC (WPS) to your TV. You can connect
devices to the TV even if a sharer is not connected to the TV.
✎
To use the Internet@TV, the AP (access point) must be
connected to the wireless network.
✎
If a Samsung Wireless Lan Adapter is connected to the
USB 2 port, the network may not operate normally. We
recommend to connect to
✎
Only sharers using the 2.4 Ghz band are supported.
Sharers using the 5 Ghz band are not supported.
SWL connect
You can directly connect a device that supports the PBC
(WPS) to the TV.
✎
This function is available when
Wireless Link) is set to On.
port.
USB 1 (HDD)
SWL(Samsung
How to connect Samsung Wireless link
For the procedures to establish a connection, refer to the
following:
1. Follow Steps 1 through 5 in the "How to set up using
PBC (WPS)". (P. 27)
2. Select Samsung Wireless Link by using the ▼ button
and press the ENTERE button to turn it On.
3. Select SWL connect by using the ▼ button and press
the ENTERE button.
4. If the "Press the PBC button on the device which
supports PBC button to connect within 120 seconds"
message appears, press the PBC button on the device
to connect.
✎
For more information, refer to the wireless network
setup manual of the device to be connected.
5. If the device is connected properly to the TV after
starting count on message box then message box will be
disappeared automatically.
✎
If the connection fails, please retry after 2 minutes.
If Your TV Fails to Connect to the Internet
Your TV may not be able to connect to the Internet
because your ISP has permanently registered the
MAC address (a unique identifying number) of your
PC or modem, which it then authenticates each time
you connect to the Internet as a way of preventing
unauthorized access. As your TV has a different
MAC address, your ISP can not authenticate its MAC
address, and your TV can not connect.
To resolve this problem, ask your ISP about the
procedures required to connect devices other than a
PC (such as your TV) to the Internet.
If your Internet service provider requires an ID or
password to connect to the Internet, your TV may not
be able to connect to the Internet. If this is the case,
you must enter your ID or password when connecting
to the Internet.
The internet connection may fail because of a firewall
problem. If this is the case, contact your Internet service
provider.
If you cannot connect to the Internet even after you
have followed the procedures of your Internet service
provider, please contact Samsung Electronics.
29
English