Steam Ironing; Dry Ironing - POLTI Vaporetto ECO POWER Mise En Route

2c. Press the steam request lever (3) on the steam
gun (2) or, if using the professional iron, the
steam request button (R) on the professional
iron (Q) so as to fully exhaust the steam supply
from the tank.
3c. Switch OFF the accessory on/off switch (C).
4c. Disconnect the power supply cable (F) from the
mains.
5c. Unscrew anti-clockwise the patented safety
cap (A)
6c. Wait for a few minutes to allow the generator
tank to cool down.
7c. When cool proceed to carefully refill the tank as
described in paragraph 1 of the section "Prepa-
ration for Use". If refilling the generator when
not completely cooled, pour only very small
quantities of water at each pouring into the
tank, so as to avoid spitting from the tank, and
cover exposed skin and face whilst filling
USE OF THE PROFESSIONAL IRON
(OPTIONAL)
Vaporetto can be quickly transformed into a hi-
ghly effective ironing system to make ironing
quick and easy. Simply connect the product to
the iron accessory for Vaporetto.
You may purchase the iron accessory at any
Polti service centre or from top home appliance
retailers.
1d. Connect the connector assembly at the end of
the iron hose (4) to the generator as shown in
point 2a of the section "Instructions for Use".
Check the manufacturer's label on the garment,
and interpret the symbol on the label as follows:
Steam ironing allowed
For dry ironing, set thermostat on •••
Steam ironing allowed
For dry ironing, set thermostat on ••
Check the fabric's resistance to steam
ironing or dry iron with thermostat set
on •
- do not iron
- steam ironing or treatment not al-
lowed

STEAM IRONING

2d. For STEAM ironing, turn the dial (S) and set the
iron temperature to its maximum travel on the
"COTTON-LINEN" steam position.
Most types of fabric, other than delicates can
be STEAM ironed at this temperature, please
VAPORETTO ECO POWER
7
consult the garment manufacturer's instruc-
tions on the label.
NB FABRIC INDICATIONS ON DIAL ARE
FOR DRY IRONING, NOT STEAM IRONING.
3d. Wait for a few minutes until the "Iron heating"
indicator light (V) goes out, to show that the so-
leplate of the iron has reached the required
temperature.
4d. Press the steam request button (R) to enable
the steam to come out. The steam flow will stop
when the button is released. After each filling,
when you first start to use the iron, a few drops
of water mixed with the steam may be emitted
(due to imperfect heat stabilisation). It is there-
fore advisable to direct the first jet of steam
onto a rag.
5d. The iron can also be used in a vertical position
e.g. for removing creases from curtain, clothing
etc.
6d. To obtain a continuous jet of steam move the
sliding button (U). The steam will continue to
come out even when the steam request button
(R) is released. To stop the steam flow move
the sliding button backwards (U).

DRY IRONING

7d. If you need to DRY iron (ONLY) (NOT steam
ironing), press the accessory on/off switch (C)
and adjust the temperature of the iron by turn-
ing dial (S) to the temperature required for the
fabric (as shown on the dial).
ATTENTION: when dry ironing, be careful not
to press the steam request button (R), as hot
water could come out of the iron onto your gar-
ment and board.
IMPORTANT
• Do not leave the iron unattended whilst con-
nected to the mains.
• Iron only on heat resistant surfaces and on sur-
faces that allow the steam to escape e.g. MESH
ironing boards.
• ATTENTION: if you iron sitting down, do not
place your legs under the ironing board, the
steam can cause burns.
TIPS FOR BETTER UNIT
PERFORMANCE
WARNINGS
• For cleaning leather, wood or delicate fabrics
especially dralon, velvet and other pile surfaces,
consult the manufacturers instructions. Clean
only by using the hand gun at a safe distance to-