Operating The Appliance - British Fires NEW FOREST ELECTRIC Guide D'installation Et Mode D'emploi

//

12.0 OPERATING THE APPLIANCE

Standby Button: Heating Operations:
1)
Turns the appliance ON/OFF Press the heater button to turn
standby, the default settings are: the heating function on and off
heater set to 82°F/27°C, the and adjust the temperature
main flame effect is F1, the Fuel setting. Heater is divided into
bed is L1 (no temperature display). temperature settings: 62°, 63°,
64°, 65°, 66°, 67°, 68°, 69°, 70°,
Changing Flame Effect:
71°, 72°, 73°, 74°, 75°, 76°, 77°,
In the power-on state, press this
78°, 79°, 80°, 81°, 82°, ON, 62°F.
button, the digital screen displays
(Circular operation control)
the flame position and the flame
indicator is bright, and the main 2)
Press and hold the heater
flame position can be adjusted. button for 3 seconds to convert
The flame brightness settings are:
the temperature unit from °C to
F1, F2, F3, F4, Set as follows:
°F. The temperature display
Button Display Flame Effect window will flash. After the
temperature is set, the display
1st Press F1 Full
unit will flash 5 times, then
2nd Press F2 Medium
3rd Press F3 Low automatically save the settings
and exit the setting state. After
cycle through
4th Press F4
settings
the display unit is turned on, if
there is no operation within 10
seconds, the setting status is
also exited.
// 31
3) Fan delay function: 4)
After the This appliance has a non-self-
appliance is turned off, the fan will resetting overheat protection
continue running for 15 seconds device (thermal cut-out) which will
then stop. activate if the air inlets or outlets
are obstructed. For safety
Open Window Detection function:
reasons the fire will NOT switch
When the appliance is heating
on again automatically, the
and the ambient temperature
following procedure must be
suddenly drops ≥–5°C (9°F) within
carried out before the fire can be
10 minutes, and the environment
operated.
cannot be warmed up within 30
minutes the appliance will NOTE: The flame-effect will remain operational if
the cut-out is activated, only the fan heater is
automatically display "OP". The
prevented from working.
heating function will then be
Switch OFF the appliance at the
automatically turned off, and when
wall socket or outlet. Leave the
the "OP" is displayed, it can be
fire OFF for a period of no less
turned off and then restarted by
than 10 minutes, ensuring all
turning off and on the appliance to
obstructions are removed. Switch
clear the fault code.
the appliance ON at the wall.
Ensure the appliance is turned ON
at the control switches. If the fire
fails to operate correctly, repeat
the above procedure.
Refer to section 13.0 for more information about
the Safety Cut-Out System.
Fuel Bed Color Options: Setting Sleep Timer:
Once powered, press the "Fuel In the timed display, press the
Bed" button and the LCD screen "Sleep Timer" button to adjust the
on the remote will display the fuel time, plus one hour for each
bed icon. Now, the fuel bed color press. (You can't enter the weekly
can be adjusted. The different timing selection, you can only set
settings are: L1, L2, L3, L4; Fuel the current automatic shutdown
bed light. Set as follows: time. This function is available
when the weekly timing function is
Button Display Flame Effect
turned on. Will not operate).
1st Press L1 Orange
Timing range: 1H, 2H, 3H, 4H, 5H,
2nd Press L2 Blue
6H, 7H, 8H, 9H, OF, 1H (cycle
3rd Press L3 Orange + Blue
adjustment).
Cycle through
4th Press L4
settings
© 2020 British Fires
Control Down Lighting:
Turns the down lighting lights on
and off.
Setting Clock and Timer:
Use the date button to choose
from Monday to Sunday or week
timer mode option. Option mode:
1-2-3-4-5-6-7-A-oF.
Clock setting:
1) At standby state (after the unit
is plugged in and before pressing
"main power"), press and hold the
Setting button on the remote for
3 seconds, the digital display will
then flash "00:00".
2) Press on the remote control
to set the hour, press the remote
control to set the minutes.
3) Press "Setting" to enter the
setting of the week timer. Press
to select Sunday to Saturday,
NOTE: The current clock must be set after the
The date symbol will light up after
initial power-on or power-off, otherwise the clock
the day is selected. When finished,
will remain "00:00" status and you won't be able
press the button to exit setting. to set the week timer function.
// 32