Cleaning And Maintenance - Royal Catering RCSS-AC250W Manuel D'utilisation

EN
3.2. PREPARING FOR USE
3.2.1. APPLIANCE LOCATION
The temperature of environment must not be higher than
40°C and the relative humidity should be less than 85%.
Ensure good ventilation in the room in which the device is
being used. There should be at least 10 cm distance between
each side of the device and the wall or other objects. Keep
the product away from hot surfaces. The device should
always be used when positioned on an even, stable, clean,
fireproof and dry surface, and be out of the reach of children
and persons with limited mental and sensory functions.
Position the device such that you always have access to the
power plug. The power cord connected to the appliance
must be properly grounded and correspond to the technical
details on the product label.
3.2.2. BEFORE FIRST USE
The parts of the device (pusher, feeder, auger, strainer,
strainer holder, collecting container, containers for pulp and
juice) should be washed, except for the base with the motor
unit. After cleaning, all components must be thoroughly
dried before the device is connected to the power supply.
3.2.3. ASSEMBLING THE DEVICE
1. Install the collection container on the base. Make sure
the container matches the base. After positioning the
container, slightly turn it clockwise - it will be locked
into place. (Note: If the container is not locked on the
base, the machine will not start).
2. Install the strainer holder and the strainer into the
container. Make sure the recess on the strainer aligns
with the dot symbol on the container.
3. Place the auger in the centre of the container and turn
it clockwise until it is seated in the appliance.
10
4. Place the feeder on the container, make sure that the
open padlock symbol on the container is aligned
with the triangle symbol on the feeder.
5. Turn the feeder clockwise until it locks into place (the
arrow on the feeder aligns with the „CLOSED" symbol
on the base).
3.3. DEVICE USE
NOTE: Before starting work, place the juice and pulp
containers under the appropriate outlets.
DEVICE CONTROL
• „ON" starts the motor
• „O" (OFF) stops the motor
• „R" (REV) reverses the auger direction.
Rev. 14.01.2022
HOW TO USE YOUR JUICER
1. Connect the appliance to the power supply.
2. Before placing vegetables or fruits in the feeder, wash
or peel them (e.g. oranges, pineapples) and cut them
to fit the hole (the recommended size is no more than
7cm). Remove hard seeds (e.g. cherry, plum, apricot,
mango stones) as they may damage the juicer. Do
not put any frozen fruit, vegetables or ice into the
appliance.
3. Turn the device on using the „ON" switch.
4. When inserting vegetables / fruits into the feeder,
do not push them, the auger will automatically draw
them in. Never push fruit / vegetables down with your
hand or fingers. The pusher should only be used when
fruit / vegetables are stuck in the feeder. Put fruit /
vegetables one at a time.
ATTENTION: The juicer cannot work for more than 20
minutes - after 20 minutes wait until the motor cools
down completely.
5. In order to change the direction of the auger rotation,
set the switch to the „R" position.
6. After finishing work, turn the appliance off by
switching to the „O" position. Do not run the machine
empty as this can lead to motor overheating.
Disconnect the appliance from the power supply.
7. Clean the juicer after each use.

3.4. CLEANING AND MAINTENANCE

a) Unplug the mains plug and allow the device to cool
completely before each cleaning, adjustment or
replacement of accessories, or if the device is not
being used.
b) How to disassemble:
• Turn the feeder counter-clockwise to unlock it.
• Turn the container counter-clockwise until
unlocked, lift and remove the whole. Disassemble
in the following order: auger → strainer → strainer
holder.
c) Use only mild, food-safe detergents to wash the
device.
d) After cleaning the device, all parts should be dried
completely before using it again.
e) Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
f) Use a soft cloth for cleaning.
g) Do not use sharp and/or metal objects for cleaning
(e.g. a wire brush or a metal spatula) because they
may damage the surface material of the appliance.
h) Thoroughly wash the parts of the appliance under
running water (pusher, feeder, auger, strainer, strainer
holder, container, pulp and juice containers), except
the base with the motor.
i) Do not put any parts of the appliance in the
dishwasher.
j) Clean the silicone pad in the collecting container
with water. After each cleaning, make sure that it is
properly seated in the container.
Rev. 14.01.2022
EN
CLEANING BEFORE CHANGING TO
A DIFFERENT TYPE OF JUICE
To clean the device during operation, pour water through
the feeder. The water will rinse most of the residue from
the last juice. Flush the device until the water is colourless.
This process is not a substitute for the thorough cleaning
described above.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used to
construct the device can be recycled in accordance with their
markings. By choosing to recycle you are making a significant
contribution to the protection of our environment. Contact
local authorities for information on your local recycling
facility.
11