Changing The Gas Cylinder; Cleaning & Maintenance - Outwell H-22040N Mode D'emploi

UK: INSTRUCTION MANUAL
Connecting your gas grill to a gas cylinder
Please see TECHNICAL DATA table for information regarding regulator and hose. Only use a regulator
complying with EN16129 and a hose complying with EN16436. The length of the hose shall not
exceed 150 cm. Both regulator and hose must also comply with national regulations. Replace the hose
according to national regulations. Avoid twisting the hose.
Always read the manual regarding the regulator and hose.
Never leave the regulator attached to the gas cylinder if disconnected from the gas hose.
1. How to connect your gas grill to a gas cylinder depends on which model you have purchased.
Please read the instructions below for your Asado Gas Grill model.
Asado Gas Grill (651065):
To be able to use your gas grill you will need to purchase an LPG gas cylinder, a regulator and a hose.
The type of gas can be butane or propane. The regulator needs to fit the chosen gas cylinder and deliver
a supply pressure of 28-30mbar if the gas is butane. 30 or 37 mbar if the gas is propane. The hose needs
to fit the regulator as well as the gas grill. The gas grill can be used with either ¼" LH thread, 8mm ID or
10/11mm ID.
a) If your hose has an internal diameter of 8 mm, push the hose over the first ribbed half of the
removable hose stud (parts list, item16). Thread the hose and stud onto the gas inlet connection.
b) If your hose has an internal diameter of 10/11 mm, push the hose all the way over the ripped part of
the removable .hose stud (parts list, item 16). Thread the hose and stud onto the gas inlet connection.
c) If your hose is equipped with a ¼" left hand thread, thread the hose directly onto the gas inlet
connection.
The hose should be threaded hand tight plus a ¼ of a turn.
a) b)
Asado Gas Grill – DE (650786):
To be able to use your gas grill you will need to purchase an LPG gas cylinder and regulator (the hose
is supplied with your gas grill). The type of gas can be butane or propane. The regulator needs to fit the
chosen gas cylinder and deliver a supply pressure of 50mbar. The hose needs to fit the regulator as well
as the gas grill. The gas grill is equipped with a ¼" LH thread.
The supplied 80 cm hose is equipped with a ¼" LH thread and can be threaded directly onto the gas inlet
connection.
The hose should be threaded hand tight plus ¼ of a turn.
2. Once you have successfully connected your gas grill to a gas cylinder, position the gas cylinder at the
side of your gas grill. Keep in mind that the cylinder must be kept away from heat and in a safe and
upright position.
3. Attach the regulator to the gas cylinder tap correctly (refer to the instruction manual provided with
the regulator).
4. Always Check for leaks at all joints using soapy water.
NEVER USE A NAKED FLAME TO CHECK FOR LEAKS.
6
c)
UK: INSTRUCTION MANUAL
Lighting Your Gas Grill
1. Remove the lid from your gas grill.
2. Close the tap by turning the gas tap (12) clockwise (in direction of the arrow next to the word
'CLOSED') until it stops (do not over tighten).
3. Open the regulator on the gas cylinder.
4. Use a long match or similar and place the lit match through the hole at the opposite end from the
gas tap. Carefully turn the gas tap (12) to the halfway position (in the direction of the arrow next to
the wording 'OPEN') and the burner should light.
5. Use the tap to adjust the heat.
For Your Safety – If You Smell Gas
• If there is a leak on your appliance (smell of gas), turn off the gas supply and take it outside
immediately into a well-ventilated flame free location where the leak may be detected and stopped.
If you wish to check for leaks on your appliance, do it outside. Do not try to detect leaks using a flame,
use soapy water.
• If odour persists, stop using the appliance immediately and contact your dealer or gas supplier.

3. CHANGING THE GAS CYLINDER

• Turn off the unit completely. Be careful the gas appliance could be hot.
• The gas cylinder shall be changed in a well-ventilated location, preferably outside, away from any
sources of ignition, such as naked flames, pilots, electric fires and away from other people.
• Follow the instructions supplied with the gas cylinder and gas regulator.
• To ensure a safe connection of a new gas cylinder to your appliance please follow the instructions in
the section 'Connecting your gas grill to a gas cylinder' .
• If gas pressure drops or the gas will not light, check if there is gas left in the cylinder. If there is gas left
in the cylinder the injector on the appliance might be blocked.
4. CLEANING & MAINTENANCE
• Visually check the general condition of the appliance and clean it on a regular basis
• Ensure the appliance has cooled off completely before cleaning.
• Use a wire brush, steel wool or a scouring pad to clean the griddle.
• Interior surfaces of the gas grill housing cover should also be washed with hot soapy water.
• Periodically check the burner to see that it is free from insects and spiders which may block the gas
system.
• Clean the venturi tube on the burner (11) very carefully, checking to see it is free from obstructions.
We recommend that you use a pipe cleaner to clean the venturi tube area.
• Do not manipulate with any parts sealed by the manufacturer.
• WARNING: Any modification of the appliance may be dangerous.
Venturi tube
7