Furman ELITE-16 POWER FACTOR E i Guide De L'utilisateur page 8

e -16 P F O ' M
lite Ower actOr e i wner s anual
®
Satellite and Cable Transient Voltage Surge Suppressors
The Elite-16 PF E i features transient voltage surge suppression for both cable and satellite lines utilizing standard coaxial
connectors. As these surge suppressors are in-line, they will require an additional cable to connect from their output to the
control device requiring protection.
All in-line surge suppressors feature our exclusive ground contamination free technology. This aids in eliminating audio
buzzing, and the video hum-bars that can result from typical in-line suppressors. Further, our cable and satellite suppressors
are DVR friendly as well as HD digital television ready. Both DC carrier signals as well as high bandwidth signals can pass
through our circuit. In fact the bandwidth is less than 0.5dB loss at 2 GHz!
To connect your cabling to these in-line protectors, simply follow the in and out indications marked next to the Cable and
Satellite connectors.
NOTE: It is not possible to make an in-line cable or satellite protector "maintenance-free" as we have accomplished with the 230
VAC line. This would necessitate limited signal bandwidth that would not allow the signal to pass. Under extreme conditions, it is
possible that the surge suppression in one of these devices could sacrifice itself after a catastrophic event. If the cable or satellite
signal will no longer pass through our protector, please contact your local service representative, installer or Furman for servicing.
To test this, simply disconnect the incoming and out going cable from the Elite-16 PF E i. Connect the incoming connector to the
component that formerly received the out going connector, thus by-passing the in-line protection. If the signal is present (but
not when used with the Elite-16 PF E i) then the protection circuit is damaged (assuming it worked properly before a storm or
catastrophic event).
Warranty
Furman Sound, LLC. warrants to the original purchaser of this product, the Furman Elite-16 PF E i i, that the product will be
free from defects in material and workmanship for a period of three years from the date of purchase. The purchaser of the
product is allowed fifteen days from the date of purchase to complete warranty registration by mail or on-line at the Furman
website. If the purchaser fails to complete the aforementioned registration, the warranty period will be reduced to one year
from the date of purchase.
If the product does not conform to this Limited Warranty during the warranty period (as herein above specified), purchaser
shall notify Furman in writing of the claimed defects. If the defects are of such type and nature as to be covered by this
warranty, Furman shall authorize the purchaser to return the product to the Furman factory or to an authorized Furman
repair location. Warranty claims should be accompanied by a copy of the original purchase invoice showing the purchase
date; this is not necessary if the Warranty Registration was completed either by mailing in the completed warranty card or by
registering on-line at the Furman website. Shipping charges to the Furman factory or to an authorized repair location must
be prepaid by the purchaser of the product. Furman shall, at its own expense, furnish a replacement product or, at Furman's
option, repair the defective product. Return shipping charges back to purchaser will be paid by Furman.
CoNNECTED EQUIpMENT WARRANTY: Furman Sound's Connected Equipment Warranty covers equipment that is
damaged by transient voltage (an "Occurrence") while properly connected through the Furman Elite-16 PF E i i to a properly
wired AC power line with a protective ground in an indoor location. Furman's Connected Equipment Warranty is limited to
the amount of the deductible on the Purchaser's personal property insurance policy up to $500.00. In order to make a claim
for this Connected Equipment Warranty, the Purchaser must forward a copy of his/her personal property insurance claim
for the damaged equipment to Furman and complete the Furman Connected Equipment Warranty claim form (call Furman
at (707) 763-1010 to obtain the form). Furman reserves the right to review the damaged Furman product, the damaged
connected equipment, and the site where the damage occurred. All cost of shipping damaged equipment to Furman for
inspection shall be borne solely by the Purchaser. Damaged equipment must remain available for inspection until the claim