Mounting The Antenna - Revell Control AT WORK FARM TRACTOR PLUS Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 8
4 STarT preparaTIoN
First move the switch on the rear side of
the remote control to ON (4A), then set
the switch on the underside of the model
(4B) to ON. When switching off, always
switch off the vehicle first (cf.4B)! And
after it the remote control (cf.4A).
Otherwise, a drive command can
accidentally be triggered, causing the
vehicle to drive away on its own, which
can lead to considerable damage.
6 vehICle CoNTrol
6A In order to drive forwards, push the lever for forward and reverse travel on the left
side of the remote control forwards.
6B In order to drive backwards, push the lever for forward and reverse travel on the left side
of the remote control backwards. The model stops instantly after the lever is released.
6C In order to drive along curves, move the steering wheel in the centre of the remote
control in the corresponding direction.
6D An additional available trailer can be controlled with the two left and right levers
on the upper side of the remote control.
6E With the right-hand lever on the remote control, the front bucket of the tractor can be
raised and lowered. A soft clatter of the slip clutch can be heard at the top and bottom
limit positiv.This is completely normal.

7 MouNTINg The aNTeNNa

The accompanying antenna must be mounted on the remote control. For this purpose,
guide the end of the antenna to the thread on the upper side of the remote control
and turn clockwise until hand-tight. The range of the model is significantly decreased
without the antenna.
8 CoNNeCTINg The TraIler
8A To attach the trailer, the lock of the clutch must first be lifted slightly and then
folded back again.
8B That way, the ball folds down again and the drawbar can be guided in easily.
8C Raise the lever of the trailer coupling and slide it forward to lock the trailer on
12
5 STeerINg TrIM adjuSTMeNT
The correct trim is a basic requirement
for fault-free driving behaviour from the
vehicle. Adjusting the trim is easy, but it
requires a little patience and a feel for it.
Please follow the following
instructions precisely:
if the vehicle pulls to the left or the
right without being steered...
use the trim lever to correct the wheel
alignment by turning it in the opposite
direction. The wheel alignment can be found
on the bottom of the vehicle (cf. 5).
INSTruCTIoNS For SaFe drIvINg
GENERAL DRiViNG TiPS:
• Always maintain visual contact with the vehicle and do not look at the remote control!
• On initial driving attempts, there is a general tendency toward excessive movements
of the controls. Make sure that you have sufficient room.
After a crash, always release the speed control immediately in order to prevent dama-
ge to the electronics.
ThE SuiTABLE DRiViNG ENViRONMENT:
The location in which the vehicle is driven should fulfill the following criteria:
1. It should be a location in which there is as much open area as possible, without
disruptive obstacles.
2. Make absolutely sure when starting that there are no people or animals in the
immediate vicinity.
3. Always watch the vehicle so that it does not drive into the operator, other people or
animals and injuries them.
TrouBleShooTINg
Problem:
The vehicle does not move.
Cause:
• The batteries are too weak and/or depleted.
• The batteries were possibly not inserted correctly. Please observe the polarity
Remedy:
indication in the model
• Please replace with new batteries.
Problem:
Remote control does not work.
• The remote control is switched off.
Cause:
• The batteries were not inserted correctly.
• The batteries do not have enough power.
• Repeat the switch-on process as described.
Remedy:
• Check whether the batteries are inserted correctly.
• Please replace with new batteries.
Problem:
The vehicle cannot be controlled with the remote control.
• The remote control is switched off
Cause:
• The connection between the remote control and vehicle has been severed.
• Move the remote control switch to the "ON" position.
Remedy:
• When the model is further than 5 metres away, move towards the model
Additional tips and trick can be found online at www.revell-control.de.
ServICe guIdelINeS
At www.revell-control.de, you can find our possibilities
to order, replacement tips for spare parts, and further
useful information on all Revell Control models.
www.revell-control.de
13

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

24962

Table des Matières