Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
FEATURES
Powerhead Assembly - Houses the
electrical and mechanical components.
Cooking Rack - Offers two levels of cooking.
Lower level for taller foods, flip rack to Upper
level for appetizers.
Liner Pan - Always use liner pan when
operating your Jet Stream 2 oven. Lined with
non-stick coating for easy cleaning.
Base - Frame for the liner pan and powerhead.
Always use base when cooking.
OPERATION
1. After cleaning all parts and preparing your food. Place rack
with food into liner pan and position powerhead onto raised
handle of base. Be sure to align notch in powerhead with the
protrusion on the handle (see image) or the unit will not work.
2. Plug cord into 120V AC electrical outlet and program your
oven settings and press START to begin cooking.
Control Panel functions:
Display - Two upper right digits refer to the time setting. Will count down to zero
and automatically stop cooking. To the upper left is a rotating light indicating the unit
is operating. Bottom numbers indicate temperature setting of the oven.
FAN SPEED - Press to control fan speed. HI for meats and larger food loads. LO for
appetizers and reheating.
UP arrow "˄" - Increases the time or temperature setting.
DOWN arrow "˅" - Decreases the time or temperature setting.
TIME mode - Press to enter mode, adjust using arrow buttons. Can be adjusted
anytime before or during the cooking cycle. Press START after each adjustment.
TEMP mode - Press to enter mode, adjust using arrow buttons. Can be adjusted
anytime before or during the cooking cycle. Press START after each adjustment.
START button - Press to begin cooking.
STOP button - Press once to pause cooking. To resume cooking press START button.
Fan Operating Signal (blue)
Time Setting (green)
(0 - 99 minutes)
Temperature Setting (red)
(200°F - 400°F)
000
HI
TIME
000
LO
FAN
TEMP
SPEED
Fan Speed Setting (red)
2
Default Settings - After the cord has been plugged into the electrical outlet the
powerhead control panel will display default settings of zero time, zero temperature
and low fan speed.
Setting Cooking Time - Press TIME button then "˄" up arrow to increase cooking
time and press "˅" down arrow to decrease cooking time. ( range 0 to 99 minutes ).
The cooking time can be adjusted while the oven is stopped or during the cooking
cycle. Display will show cooking time remaining. When time expires, the display will
flash "00" and the powerhead will run for one additional minute. An audible signal
is given when finished. You may then remove the powerhead and set aside on a flat
and stable surface.
Setting Cooking Temperature - Press TEMP button then "˄" up arrow to increase
cooking temperature and press "˅" down arrow to decrease cooking temperature.
( range 200°F to 400°F degrees) . The cooking temperature can be adjusted while the
oven is stopped or during the cooking cycle.
Setting Fan Speed - Press to switch to alternate between HI and LO fan speed.
Lighted circle indicates current setting. Can be adjusted before or during the cooking cycle.
Control Cooking Cycle - After desired settings have been made, press START to begin
cooking cycle. To pause, press STOP key. The
powerhead can be set aside on a flat and stable
surface (as shown) if you want to check food or
add sauces or seasonings. Return powerhead
to base and press START to continue cooking.
Press and hold STOP key to stop the cooking
cycle and reset to default settings.
NOTE - If the powerhead is removed
at anytime from the base, it will stop
working. Powerhead must always be positioned on base to operate.
CARE AND CLEANING INSTRUCTIONS
1. Press and hold STOP key for 5 seconds and remove cord from electrical outlet.
Allow all parts to cool completely.
2. Wipe the Powerhead with a soft wet cloth and mild cleaning solution. Wipe dry with
soft towel. Never immerse powerhead in water or other liquids!
3. Clean Base with a soft, wet cloth and mild cleaning solution or place in the top rack
of the dishwasher. Rinse and Dry completely.
4. Clean Liner Pan by soaking with water and mild cleaning solution for several
minutes and clean with soft cloth or soft brush. Rinse and dry completely.
5. Clean Rack by soaking with water and mild cleaning solution for several minutes
and clean with soft cloth or brush. Rinse and dry completely!
6. NEVER USE AGGRESSIVE CLEANERS OR METAL SCOURING PADS TO CLEAN
COMPONENTS .
START
STOP
OPERATION
3
Publicité
Table des Matières
