Goelst 6000 Serie Manuel page 14


NL EN DE FR
WM001C
WM001G
WM001C
WM003C1G
WM001G
WM001C
2
WM003C1G
WM001G
WM001C
2
WM003C1G
WM001G
WM001C
2
WM003C1G
WM001G
2
WM003C1G
− In the event of a power cut, the positions in the motor unit will be maintained.
!
− If the system/curtain is moved without power supplied/during a power cut, it will lose its
reference positions and the system end positions will need to be re-entered.
2
Adding/removing curtain positions
In order to change or add curtain positions in a system, you must repeat the above steps 1 to 6
of "programming curtain positions" for that system.
Changing button functions for opening and closing
Repeat the procedure "programming curtain positions" wereby the opposite buttons for opening
and closing the curtain are selected.
For several linked systems: Remember that changing the "open" and "close" positions will
!
have consequences for any central control of linked systems: for example, a central "close"
command will result in the system being operated.
WM003C WM009C
STEP 1
Use the remote control (Open/Close buttons) to ensure a distance of 20
cm (8 inch) or more between the overlap carrier and the end pulleys.
WM002G WM003G
STEP 2
WM003C WM009C
Using the transmitter, keep the stop button pressed: a
green led will start flashing in the bottom of the motor unit,
release the button only when the LED flashes red (after
approx.8 seconds). The system overlap carrier will move
briefly in both directions.
WM006G WM004G
WM002G WM003G
WM003C WM009C
STEP 3
Press CLOSE* on the transmitter and release it when the curtain reaches
the desired position. Briefly pulse OPEN or CLOSE for further fine
adjustment.
WM006G WM004G
* The button you choose here, either open or close, will represent the
WM002G WM003G
WM003C WM009C
close function.
STEP 4
Briefly press stop to confirm the position. The system will move briefly in
the "open" direction.
WM006G WM004G
WM002G WM003G
STEP 5
WM003C WM009C
Press OPEN ** and keep it pressed until the curtain reaches the desired
position. Briefly pulse OPEN or CLOSE for further fine adjustment.
** Press CLOSE if reversed button function was chosen in step 3.
WM006G WM004G
WM002G WM003G
STEP 6
Briefly press stop to confirm the position. The system will move a short
distance in the "close" direction.
The red LED on the bottom of the motor unit goes out. The positions are
set and the rail is ready for use.
WM006G WM004G
EN Range of NiceWay transmitter modules
IT Gamma dei moduli-trasmettitore NiceWay
FR Gamme des modules-émetteur NiceWay
ES Gama de los módulos-transmisores NiceWay
DE Die Reihe der NiceWay Sendermodule
PL Gama modułów-nadajników NiceWay
NL Assortiment zendmodules NiceWay
EN Range of NiceWay transmitter modules
IT Gamma dei moduli-trasmettitore NiceWay
FR Gamme des modules-émetteur NiceWay
WM080G
ES Gama de los módulos-transmisores NiceWay
DE Die Reihe der NiceWay Sendermodule
A B
C D
Gama modułów-nadajników NiceWay
PL
NL Assortiment zendmodules NiceWay
EN Range of NiceWay transmitter modules
IT Gamma dei moduli-trasmettitore NiceWay
FR Gamme des modules-émetteur NiceWay
WM080G
ES Gama de los módulos-transmisores NiceWay
DE Die Reihe der NiceWay Sendermodule
A B
C D
PL Gama modułów-nadajników NiceWay
NL Assortiment zendmodules NiceWay
EN Range of NiceWay transmitter modules
IT Gamma dei moduli-trasmettitore NiceWay
FR Gamme des modules-émetteur NiceWay
WM080G
ES Gama de los módulos-transmisores NiceWay
DE Die Reihe der NiceWay Sendermodule
A B
PL Gama modułów-nadajników NiceWay
C D
NL Assortiment zendmodules NiceWay
EN Range of NiceWay transmitter modules
IT Gamma dei moduli-trasmettitore NiceWay
FR Gamme des modules-émetteur NiceWay
WM080G
ES Gama de los módulos-transmisores NiceWay
DE Die Reihe der NiceWay Sendermodule
A B
C D
PL Gama modułów-nadajników NiceWay
NL Assortiment zendmodules NiceWay
WM080G
A B
C D
WM240C
A B
C D
WM240C
A B
C D
WM240C
A B
C D
WM240C
A B
C D
WM240C
A B
C D