Mixer Section - Gemini CDM-3610 Manuel D'instructions

causes the operation to change from PLAY to PAUSE or
from PAUSE back to PLAY. The PLAY/PAUSE BUTTON
remains lit when in PLAY mode, while it blinks in PAUSE
mode.
CUE: To set a CUE point, press the PLAY/PAUSE BUTTON
24
while a file is playing and use the JOG WHEEL to locate
a desired CUE point. Pressing the PLAY/PAUSE BUT-
TON again will set a CUE point. While the unit is playing
and after the cue point has been programmed, pressing
CUE will cause the CD player to enter the PAUSE mode
(PLAY/PAUSE BUTTON blinks) at the programmed cue
point (the CUE LED is lit). Holding down the CUE but-
ton changes the function to preview, and allows you to
stutter start or play from the programmed CUE POINT.
Releasing the CUE button will return the CD to the preset
CUE point.
TRACK SELECTION ROTARY: The TRACK SELECTION
25
ROTARY allows you to select the next or previous track
by either turning it clockwise to go forward or counter-
clockwise to go back. Select the track desired by press-
ing the TRACK SELECTION ROTARY.
NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK,
YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE
POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER
AGAIN, THE CUE WILL BE PRESET TO THE BEGINNING
OF THE NEWLY SELECTED TRACK.
BRAKE: To engage the BRAKE function, press the
26
BRAKE button, then press the PAUSE button to perform
the brake effect. To restart the song, press the PAUSE
button.
REVERSE: When the REVERSE button is pressed, the file
27
that is currently playing begins to play in reverse mode.
SEARCH: The SEARCH feature allows the operator to go
28
forward or backwards in time on the current track as-
signed to that channel.

MIXER SECTION:

29 CHANNEL INPUT SELECTOR: The CHANNEL INPUT
SELECTOR switches allow you to choose which input
will be controlled by that channels corresponding vol-
ume FADER. For example CHANNEL (1) INPUT SELEC-
TOR allows you to choose between line (1) (That sides
internal CD player), line (2) which is line input RCA (1)
and or PHONO (1) (if the CONVERTIBLE LINE SWITCH
is switched to PHONO) see above. The same applies for
channel 2.
30 CHANNEL ROTARY GAIN: The CHANNEL ROTARY GAIN
allows you to boost the signal of each individual channel
depending on how low or high its input level is.
6
3-BAND EQUALIZER: The 3-BAND EQUALIZER adjusts
31
the tone of each CHANNEL by giving you a choice 3 fre-
quencies (BANDS) to adjust, from LOW, MIDRANGE (MID)
and HIGH's, you can use the adjustment knobs to higher
or lower the 3 separate frequencies till the sound of the
music program is appropriate for your listening environ-
ment.
32
CHANNEL VOLUME FADER: After you have chosen which
input you will use with the INPUT SELECTOR the corre-
sponding CHANNEL FADER will allow you to adjust the
volume for that particular CHANNEL.
CHANNEL CUE SELECTOR: The CHANNEL CUE SELEC-
33
TOR allows you to choose which channel you wish to
monitor in your headphones, to the left is CHANNEL (1) to
the right is CHANNEL (2).
CUE VOLUME ROTARY KNOB: The CUE VOLUME RO-
34
TARY KNOB adjusts your HEADPHONE MONITOR OUT-
PUT'S volume.
35
MICROPHONE VOLUME ROTARY KNOB: Allows you to
adjust the volume of the microphone signal.
36 MASTER OUTPUT ROTARY KNOB: The MASTER OUTPUT
rotary knob adjusts the volume of the MAIN MASTER out-
put.
VU METER: The CDM-3610 has a stereo VU METER that
37
allows you to monitor the decibel levels of the LEFT and
RIGHT MASTER output.
FADER START BUTTON: The Fader Start function allows
38
you to start CD playback simply by moving the CROSS-
FADER from side to side.
A. Cue up the CD player you wish to start using the
Fader Start function
B. Move the CROSSFADER all the way to the opposite
side of the CD you have just cued.
C. Press the FADER START SELECTOR button so that
the button becomes illuminated.
D. At the point in which you wish to start the audio
from the cued CD, simply move the CROSSFADER in
the direction of the cued CD player, and playback will
begin.
E. When the CROSSFADER is moved all the way to the
opposite side of the currently playing disc, the unit will
stop playing that disc and return to the beginning of
the track or the set cue CDM-3610 point.
CROSS FADER: The CROSS FADER allows you to mix
39
evenly from one source to another. The CROSS FADER on
the CDM-3610 is also removable and if the need arises
can be replaced. The RG-45 (RAILGLIDE™) DUAL-RAIL
CROSS FADER, which has internal dual stainless steel
rails that allow the slider to ride smoothly and accurately
CDM-3610