Accessories - Silverline DIY 650W Mode D'emploi

GB
Grinding
• Only use discs specifically manufactured for grinding operations. Stone and metal grinding discs
are not interchangeable. Use the correct disc for the application
• When grinding, keep the tool at approximately 15 to 30° to the workpiece surface (Fig. VI)
Note: Do not apply too much pressure to the tool whilst grinding. Excessive pressure does not result
in more effective removal of material, but will in fact cause premature wear of the grinding disc and
will increase wear and tear on the tool.
Cutting
WARNING: Always ensure the correct guard (optional accessory) for use with cutting discs or
superabrasive wheels is installed.
Note: This machine is not designed for wet cutting.
• Only use discs specifically manufactured for cutting operations. Stone and metal cutting discs are
not interchangeable. Use the correct disc for the application
• Never use cutting discs for grinding operations. The disc might shatter and produce projectiles
that could injure the operator and/or bystanders
• When cutting, always keep the angle of the disc constant. Do not apply any sideways force to
cutting discs, as this might lead to the disc becoming jammed in the cut and shattering
WARNING: Do not apply too much pressure to the tool whilst cutting. Excessive pressure does not
result in more effective or faster cutting, but will in fact cause premature wear of the cutting disc and
increase wear and tear on the tool.
Note: The cutting disc will wear during use, and the disc diameter will gradually reduce in size. The
smaller the disc becomes, the more strain will be placed on the motor. Avoid damage to the tool by
only using cutting discs that fall within approximately 25% of the original size.
Using a cup brush or wire wheel
• Always check the no-load speed of the grinder does not exceed the maximum speed of the cup
brush or wire wheel
• Ensure no part of the cup brush or wire wheel can come into contact with the tool housing
• Run the grinder, with cup brush or wire wheel attached, for at least 30 seconds before use to
check that the cup brush or wire wheel is secure and properly balanced
• When using a wire cup brush or wire wheel, avoid applying excess pressure. Using greater force
will not make the cup brush or wire wheel more effective, but will bend the wires out of shape
and damage the brush

Accessories

• A full range of accessories including cutting guard and abrasive discs is available from your
Silverline stockist
• Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any inspection,
maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear. This advice also applies
to extension cords used with this tool
• if the replacement of the supply cord is necessary, this has to be done by the manufacturer or his
agent in order to avoid a safety hazard
Troubleshooting
Problem
No function when ON/OFF Slider
Switch (5) is operated
Cutting disk is off centre/vibrating
eccentrically
10
Possible cause
No power
Defective ON/OFF Slider Switch
Grinding/cutting disc is overly worn
Deformed grinding/cutting disk
Grinding/cutting disc not fitted correctly
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the machine's service life. Clean the body of your machine with a soft brush, or dry cloth.
If available, use clean, dry, compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do not use alcohol, petrol or
strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
Replacing the brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
To replace the brushes:
1. Unscrew the motor cover screw (Fig. VII)
2. Slide the cover off the tool
3. Disconnect the wire terminal from the brush (Fig. VIII)
4. Unscrew and remove the brush housing with the brush (Fig. IX)
5. Using a screwdriver (not supplied) remove the brush from the housing (Fig. X)
6. Replace the worn brush
7. Repeat process for second brush
8. Reassemble the tool in reverse order to disassembling
Note: One set of Spare Carbon Brushes (11) is supplied with this tool. Always replace both brushes
as a pair.
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
Address:
Toolstream Ltd
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools
Solution
Check power supply
Replace the ON/OFF Slider Switch at an authorised Silverline service centre
Turn 'OFF' the grinder, remove and replace the disc, as instructed in 'Fitting a
grinding or cutting disc'
Turn 'OFF' the grinder, remove and replace the disc, as instructed in 'Fitting a
grinding or cutting disc'
Turn 'OFF' the grinder, remove and replace the disc, as instructed in 'Fitting a
grinding or cutting disc'