Specific Safety Instructions; Placement Tool - stayer PR10E Instructions D'emploi

This machine is designed for cutting different wooden
profiles as, for example, decoration in one rail for grooves,
windows, wooden frames, etc. There is a large variety of
cutters for achieving different profiles.
This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates of
our machines on the website: www.grupostayer.com

2. Specific safety instructions

Do only hold the electrical tool by its isolated grips,
as the milling cutter might come to damage the
power cable. Contact with conductors under tension may
make the metallic portions of the electrical tool cause an
electrical shock to you.
Hold and secure the work piece firmly to a stable base
by means of claws or something similar. If you only
hold the work piece with your hand or press it against your
body, fastening is insecure and you may come to lose
control.
The tool's admissible revolutions must be at least
the same as the maximum revolutions stated on the
electrical tool. Those accessories rotating at higher than
the admissible revolutions may come to break.
Milling cutters and other tools used must fit perfectly
in the tool holder (claw) of your electrical tool. As tools
that do not correctly fit in the tool holder of the electrical
tool rotate out of center, they generate excessive vibrations
and may make you lose control over the apparatus.
Only bring the electrical tool near to the work piece
when in operation. Otherwise it may succeed that the
apparatus may recoil abruptly when the tool gets hooked
in the work piece.
Keep your hands away from the cutting area and from
the milling cutter. Hold the additional grip with your other
hand. When holding the milling cutter with both hands
they cannot get harmed by the milling cutter.
Never cut on metallic objects, nails or screws. This
may damage the milling cutter and cause excessive
vibrations.
Use adequate exploring apparatus to detect possible
water and pipes or hidden electrical cables, or refer
to your local company that supplies you with energy.
Contact with electrical cables may electrocute you or
cause fire. When damaging gas pipes, this may give rise
to an explosion. Perforating a water pipe may result in
material damages or cause electrocution.
Do not use damaged or spoiled milling cutters.
Damaged or spoiled milling cutters increase friction, may
get hooked and cause unbalance.
Work on a firm base holding the electrical tool with
both hands. It is safer to guide the electrical tool with both
ENGLISH
18
hands.
Wait until the electrical tool has stopped before
depositing it. The tool may get hooked and make you
lose control over the electrical tool. The connector
plug must only be connected to a socket having the same
technical features as the plug at hand.
3. Instructions for use

3.1 Placement tool

For your safety, make sure that you work at a clean, stable
and clear place.
There is a large variety of cutters for achieving different
profiles. Some cutters are excessively large to allow
extraction of dust for fitting. In those cases it is especially
important to use protecting masks as breathing the dusts
may cause respiratory diseases.
3.2 Assembly
Before any handling of the electric tool, unplug the
plug from the power socket. Read, understand and
apply the manual provided. Take the machine out of
the box together with its accessories. See the list of
components to obtain information on the accessories
and parts of the machine.
PR10E
EXTRACTING THE CUTTERS
The machine is supplied with 6 tongs and 6 strawberries.
Press and hold the lock button on the axis to stop the
spindle.
While pressing the lock button axis loosen the collet nut
(one piece) by turning counterclockwise to clockwise,
using the key (supplied).
INSTALLING MILLING CUTTERS
Remove the collet nut. Insert cutter into collet nut.
Tighten the nut assembly of the clamp pressing and
holding the lock button axis, after tightening the collet nut
by hand and then secure using the key (supplied).
WARNING: make sure the collet nut is seated properly
before starting work.
PR6 / PRP6
Insert the bit all the way into the collet cone and tighten the
collet nut securely with the two wrenches. To remove the
bit, follow the installation procedure in reverse.
CAUTION:
• Do not tighten the collet nut without inserting a bit, or the
collet cone will break.
• Use only the wrenches provided with the tool.
To adjust the bit protrusion, loosen the lever and move the
tool base up or down as desired by pressing and turning
the adjusting roller. After adjusting, tighten the lever firmly
to secure the tool base.
ROUTER BASE OF THE MACHINE (PR10E)
Router base "L" is connected to the cutter and allows the
machine to follow a special cutting profile.
18