Troubleshooting Guide - Guardian Technologies H1510 Utilisation Et Instructions D'entretien

CLEANING
1. Always unplug the unit before servicing in any way.
GENERAL CLEANING
2. Water tank. Empty water tank. Remove mist spout and clean with fresh water
and a light brush (bottle cleaning brush is recommended).
3. Outer surface of the unit. Wipe the surface of the unit with a soft, damp cloth if needed. If you notice
an accumulation of water during usage, reduce humidity and dry outer surface with a cloth.
DESCALING
• Depending on usage and water type, cleaning to remove scale may be required
weekly or every other week to optimize unit performance.
• If you live in a hard water area, we recommend the use of distilled water for your
humidifier. This will help reduce the precipitation of minerals or 'white dust'.
• Do not clean the unit or water tank with detergents or cleaning chemicals of any kind.
ULTRASONIC DISK
1. Unplug unit.
2. Remove the tank and empty all water from unit base and tank.
3. Locate the ultrasonic disk on the inside center of the base unit.
4. Use ONLY the enclosed cleaning brush to gently clean disk
and remove build up and deposits. Do not scrub or scrape
the ultrasonic disk.
If scale becomes difficult to remove with brush:
1. Fill the Base with: mixture of 1 tsp. white vinegar and 1 tsp. water.
2. Let solution stand for 5 minutes.
3. With the vinegar in the Base, clean all interior surfaces with a soft cloth or brush to help remove scale.
4. Also check mist nozzle and mist tube in water tank. Clean as needed.
5. Rinse the Base thoroughly with water to remove scale and vinegar solution.
END OF SEASON STORAGE
• Follow the Cleaning and Descaling instructions when the humidifier will be stored at the end of the season.
• Dry the humidifier completely before storing. DO NOT store with water inside the Base or Water Tank.
• Pack the unit in its original carton and store in a cool, dry location.
NOTE: IF YOU EXPERIENCE A PROBLEM DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING
YOURSELF. DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE HUMIDIFIER
OR PERSONAL INJURY.
E-6
Ultrasonic Disk
*Clean the disk with the brush only.
No other cleaning tool should be
used. BRUSH ONLY.
TROUBLE SHOOTING GUIDE
PROBLEM
SOLUTION
Power Plug: Unplug and then try again.
Water vapor and humidity
are not produced. Power Failure: When the power is returned, try again.
Tank Installation: Make sure the tank is correctly attached.
The surface of the ultrasonic disk is dirty: Clean ultrasonic disk.
Excessive Water: Remove a certain amount of water from the tank.
Air blows but water vapor
is not produced.
The desired humidity is lower than the current temperature:
Increase the desired humidity.
Detergent residue and/or oil ingredients from cosmetics, etc. may be in
tank; wash out tank and try again.
The surface of the ultrasonic disk is dirty: Clean ultrasonic disk.
If you use hard water, replace with softer water.
The surface of the ultrasonic disk is dirty: Clean ultrasonic disk.
Humidity level is low.
The water in the unit is too cold: Replace with cool, but not cold water.
Damage on the ultrasonic disk: Contact Customer Service
Poor maintenance or dirty water: Clean the product thoroughly,
The humidity has
and fill it with fresh water.
a bad smell.
Hard water may deposit a certain amount of dust. Dust in the air also
White dust is forming on
settles because of added humidity in the room. Use distilled water if
nearby furniture.
this becomes a nuisance.
No or low water. Unplug unit and replace water bottle.
Unit has stopped working.
Light on front of unit is red. No or low water. Unplug unit and refill tank.
Unit has stopped working.
Saturation of humidity. Lower mist control setting.
Water is accumulating outside
Unit not level and water is accumulating. Unplug and place on level
of unit or area surrounding unit.
surface. Point spray away from objects. Raise unit on a water-resistant
level surface 2-3 feet off of floor.
Unit must be placed on a at, level, hard surface. Make sure it is NOT
Increased noise level.
placed on a soft or absorbent surface.
E-7