Inspection; Operation - Lincoln Electric PowerLuber A Serie Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Models 1800, 1842, 1842E, 1844, 1844E
PowerLuber Grease Gun

INSPECTION

Visually inspect for damaged, loose or miss-
ing parts. If equipment is worn or damaged,
remove from service. Contact an authorized
service center for damage assessment or
repair.

OPERATION

Changing "L" or "H" Mode
To change the mode of operation:
To prevent damage to the gears in the
transmission, the motor must be com-
pletely stopped before changing the lever
to the "L" or "H" (low or high) mode of
operation.
"L" (low output/high pressure)
"H" (high output/low pressure)
When motor is not running, push the lever
(Fig. 1) until letter "L" or "H" will be completely
visible in the window.
In case the lever is not completely shifted/
engaged, hold this lever and bump the switch
to engage gears.
High output is recommended if the tool is
used to lubricate large bearings not requiring
high pressure, beyond 3,000 PSI (206 bar).
Also, high output is recommended if tool is
used to reill small reservoirs of the automatic
lubrication systems.
Low output is recommended if the tool is
used in construction, mining applications and
general lubrication. Low output will provide
the maximum pressure of up to 7,000 PSI
(482 bar) the tool is capable of producing.
Prime the PowerLuber after each reill or
grease cartridge change. Prime the gun
before using it to lubricate grease points.
To prime, operate the gun until grease lows
from the hose. Use vent valve (Fig.1) to expel
air pockets.
Installing Grease Cartridge
1. Unscrew the grease tube assembly from
the PowerLuber.
2. Visually check the follower seal lip direc-
tion before loading a new cartridge. The
follower seal lip must be directed toward
the follower handle or rear side for car-
tridge loading. See Fig. 2. (To change the
Page Number - 6
direction of the follower seal, unscrew tube
cap from grease tube assembly and pull on
the handle to remove follower seal from tube.
Flip follower seal over and reassemble.)
3. Pull back on the follower handle and latch the
follower rod groove into the slot on the tube
cap.
4. Remove the plastic cap from the grease
cartridge and insert cartridge into the
container tube.
5. Remove the pull tab from grease cartridge
and screw grease tube assembly into pump
assembly.
6. Thread grease tube assembly back onto the
Powerhead.
7.
Release follower rod from slot. Purge air
from pump. See air purging instructions.
Air pockets in the cartridge lubricant will
cause the gun to lose its prime.
Removing Empty Grease Cartridge
1. Pull back on the follower handle until the
follower rod is fully extended and latch the
follower rod groove into the slot on the tube
cap.
2. Unscrew the grease tube assembly from the
PowerLuber.
3. Carefully release the follower handle to eject
the empty cartridge from container tube.
To Convert Gun to Allow Filling From
Bulk Containter or Filler Pump
1. Unscrew the grease tube assembly cap
from the grease tube assembly. Pull on the
follower handle to extract the follower and
spring from the grease tube assembly.
2. Grasp follower between thumb and foreinger
and lip the follower lip from the rear to the
front side.
NOTE. The follower resembles a cup. When
the gun is assembled for use with bulk
lubricant, the cup opens toward the pump
assembly.
3. Reassemble follower into grease tube as-
sembly and position with the follower handle
so that the grease tube assembly cap can be
tightened onto the container tube.
Figure 2
Form 403994

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

180018421842e18441844e

Table des Matières