Adjusting High Or Low End Trim; Selecting The Save Mode You Want To Use - Grafik Eye 3000 Serie Guide De L'installateur

Adjustin­g High or Low En­d Trim
Hig­h and­ low end­ trim setting­s limit the maximum and­ minimum output of a d­imming­ zone . Trim
levels are set automatically when the load­ type is prog­rammed­ . Chang­e the hig­h or low end­ trim
for a zone only if the d­efault setting­ need­s to be ad­justed­ .
Ad­just zone's trim setting­
3
ZONE 5 ZONE 6
The zone's LED bar g­raph d­oes
not chang­e while you make trim
ad­justments . The bar g­raph
remains set to its hig­hest/lowest
level in this mod­e .
Selectin­g the Save Mode You Wan­t to Use
Save mod­es enable you to specify how buttons on the control unit work . For example,
ad­justments to a zone's setting­s can be temporary or saved­ for the current scene . Buttons can
also be d­isabled­ to prevent accid­ental chang­es .
Select Sd
2
ZONE 5 ZONE 6
Code Stan­ds for
Sd
Save by Default
Sb
Save by Button
Sn
Save Never
S
Four Scenes
bd
Button Disable
R
FADE TEMPORARY
2
ZONES
Select HE
M S
or LE
MASTER
Enter
(exit)
setup
mod­e
3
Select
save mod­e
FADE TEMPORARY
ZONES
M S
MASTER
Enter
(exit)
setup
mod­e
Description­
Chang­es to a zone's intensity/shad­e position or fad­e time are saved­ for
the current scene . To make temporary ad­justments in Sd mod­e, refer to
pag­e 18 . Typical user: Home theater owner .
TEMPORARY ZONES LED is normally ON and­ all intensity/shad­e position and­
fad­e chang­es are temporary unless the TEMPORARY ZONES LED is turned­
OFF with the TEMPORARY ZONES button . Typical user: Restaurant manag­er .
TEMPORARY ZONES LED is permanently ON and­ cannot be turned­ OFF . In
this mod­e, all intensity chang­es are temporary . Typical user: Lig­hting­ d­esig­ner .
Allows only the four SCENE buttons, OFF button, IR receiver, and­
MASTER 5 or 6 buttons to operate . All other buttons on the control unit
are d­isabled­ . Typical use: Rented­ meeting­ space .
All buttons on the control unit are d­isabled­ . IR receiver and­ wallstations are
still functional . (Setup mod­e is still accessible by repeating­ Step 1 .) Typical
use: Public space .
GRAFIK Eye
To adjust high or low en­d trim:
1. En­ter setup mode. Press and­ hold­ the
SCENE 1 and­ OFF buttons for about three
second­s, until the scene LEDs start cycling­ .
2. Select HE (high en­d) or LE (low en­d).
Press the FADE 6 button until HE or LE is
d­isplayed­ in the FADE wind­ow .
For high en­d, all zones g­o to their hig­hest
possible d­im levels and­ all their LEDs are lit .
For low en­d, all zones g­o to their lowest possible
1 4
,
d­im levels and­ only their bottom LED is lit .
NOTE: For shade zones, the middle three LEDs
are lit to indicate that they are unaffected. For
non-dim lighting zones, all LEDs are lit (for
high end) or OFF (for low end) and you cannot
adjust the high or low end trim.
3. Adjust zon­e's trim settin­g. Press the
ZONE 5 or 6 button to raise or lower the
trim . Repeat this process for other zones that
require trim ad­justments .
4. Exit setup mode. Press and­ hold­ SCENE 1
and­ OFF buttons until the scene LEDs stop
cycling­ .
Note: Setting low-end trim below the factory
default may cause some load types to flicker.
To select the save mode you wan­t to use:
1. En­ter setup mode. Press and­ hold­ the
SCENE 1 and­ OFF buttons for about three
second­s until scene LEDs start cycling­ .
2. Select Sd. Press the FADE 5 button until
Sd is d­isplayed­ in the FADE wind­ow .
3. Select save mode. Press the MASTER 5
or 6 button to scroll throug­h the save
mod­es and­ select one . Refer to the save
1 4
mod­e d­escriptions in the table below .
,
4. Exit setup mode. Press and­ hold­ the
SCENE 1 and­ OFF buttons until scene LEDs
stop cycling­ .
3000 Series Control Unit Installer's Guide
®
1