Silva TRAIL SPEED ELITE Mode D'emploi page 2

FULL VERSION MANUAL
TRAIL SPEED ELITE
Thank you for choosing Silva Trail Speed Elite headlamp. This ultra-
compact high power headlamp is designed for sportsmen who put
performance and weight first.
The Trail Speed Elite™ headlamp is equipped with Intelligent Light
which is a light distribution technology that combines a wide angle
flood light with a long reach spot light. This unique light image gives
the user peripheral and long distance vision at the same time. For
a runner, cross country skier, mountain biker or night orienteer
this translates into less head movement, increased control, better
balance and more speed.
PRODUCT OVERVIEW
The Trail Speed Elite headlamp consists of the following parts:
Headlamp unit
Ergonomic headset
Helmet bracket
Bike handlebar bracket
Rechargeable Li-Ion battery with battery case
Charger
Extension cable
Quick guide
BEFORE USE
BATTERY CHARGING
The battery needs to be charged before first use.
1. Connect the battery to the charger.
2. Connect the charger to the wall outlet.
3. On the charger there is an LED showing the battery status during
charging:
-green light = battery is fully charged (or not connected)
-red light = battery is charging
-blinking red light = battery is not working properly
Battery charging time is approximately 3 hours.
Note! When the battery is fully charged the charger automatically
switches to maintenance mode.
HEADSET
The elastic headset is designed to give a comfortable fit at speed ac-
tivities such as running, XC skiing etc. Adjust the headset by moving
the sliding buckle to fit it onto your head.
To remove, press the push button on the bracket and move the
bike light up and out.
BIKE HANDLEBAR ATTACHMENT
The bike handlebar attachment is designed for use on bike hand-
lebars with a dimension between 25 and 32 mm. Simply mount the
attachment by wrapping the rubber strap around the handlebar and
fasten it on the plastic hook.
Attach the bike light in the bike handlebar attachment by sliding
the bike light bracket into the snap-in socket.
To remove, press the push button on the bracket and move the
bike light up and out.
HELMET ATTACHMENT
The helmet attachment comes with a pre-mounted adhesive for
easy mounting on any helmet. It is designed to not affect the protec-
tive characteristics of the helmet.
To mount the helmet attachment, make sure the surface of the
helmet is clean and dry. Remove the protective film covering the
adhesive and press the bracket onto its correct position.
If you do not want to use the adhesive on your helmet the attach-
ment is prepared for mounting with 2 cable ties on the sides. (Not
included)
Attach the bike light in the helmet attachment by simply sliding the
bike light bracket into the snap-in socket.
To remove, press the push button on the socket and move the bike
light up and out.
FLEXIBLE BATTERY CARRYING
The battery can be carried in multiple ways; for example in a back-
pack, hip-bag or on the headset itself.
DURING USE
SWITCH ON YOUR HEADLAMP
On the side of the headlamp body there is a push button which
controls all light modes.
Each press on the button gives you the following light:
Turns the headlamp ON with all LEDs in maximum power.
Both LEDs in min mode
Flood light LED in min mode
Starts over from 1
To turn OFF the headlamp; press and hold the button for 1 second.
Art.no 37310-4
The flash function, which is used to attract attention, is started from
OFF mode by pressing and holding the button for 1 second. To turn
OFF; press and hold the button for 1 second.
TEMP CONTROL
®
Note that the headlamp body temperature will increase during use.
The headlamp temperature is depending on light mode, ambient air
temperature and the airflow (speed). The Trail Speed Elite headlamp
is equipped with a temperature control that prevents the headlamp
body from overheating by reducing the power to the LEDs.
BATTERY INDICATION
During operation of the headlamp there will be a low battery war-
ning when 20% of the battery time remains. This is done by flashing
both LEDs for 1 second and repeated again after 5 seconds.
AFTER USE
MAINTENANCE
To make sure you get maximum performance from your Trail Speed
Elite headlamp, clean it regularly with a damp cloth.
Headset cleaning – rince in warm water.
ABOUT LI-ION BATTERIES
The battery should be stored in a dry environment within the tempe-
rature range of -20°C and +35°C.
If you would like to store your battery for a longer period (more than
30 days) the battery should not be fully charged. This may cause loss
of its characteristics.
Li-Ion batteries have a discharge rate of approx. 20% over a 30 day
period. You can always charge a half full battery without damaging
its characteristics.
Do not expose the battery for extreme temperatures which may
cause fire or explosion.
Do not disassemble or mistreat the battery, risk for chemical burn.
Keep away from children.
Do not dispose of batteries in fire. This may cause an explosion.
Do not submerge the batteries in water.
Do not short circuit the contacts.
Replace only with Silva Trail Speed Elite batteries.
Note! Always make sure to disconnect the battery when the head-
lamp is not used.
TECHNICAL SPECIFICATIONS
Weight: headlamp (including head bracket): 62 grams
Battery weight: 100 grams
Battery type: Li-ion 7.4V, 2.5 Ah
Light distance (Max/Min): 90 m/55 m
Lumen: 660
Burn time: Max/Min/Wide/Flash: 2,5 hours/10 hours/10 hours/20
hours
Water resistance: IPX6
Operative temperature range: -20 - +60º
PROTECT THE ENVIRONMENT.
Headlamp and batteries should be recycled and must not be thrown
in the regular trash. Dispose these items in accordance with appli-
cable local regulations.
WARRANTY
Silva warrants that, for a period of two (2) years, your Silva Product
will be substantially free of defects in materials and workmanship
under normal use. Silva's liability under this warranty is limited to
repairing or replacing the product. This limited warranty extends
only to the original purchaser.
If the Product proves defective during the Warranty Period please
contact the original place of purchase. Make sure to have your proof
of purchase on hand when returning the product. Returns cannot
be processed without the original proof of purchase. This warranty
does not apply if the Product has been altered, not been installed,
operated, repaired, or maintained in accordance with instructions
supplied by Silva, or has been subjected to abnormal physical or
electrical stress, misuse, negligence or accident. Neither does the
warranty cover normal wear and tear. Silva is not responsible for any
consequences, direct or indirect, or damage resultant from use of
this product. In no event will Silva's liability exceed the amount paid
by you for the product. Some jurisdictions do not allow the exclusion
or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This Warranty is valid
and may be processed only in the country of purchase.
For more information please visit www.silva.se
Visit: www.silva/enviroment
for more information about the
Waste Electrical and Electronic
Equipment (WEEE) Directive.