Technical Data; Scope Of Supply - Roller 'S Robot 2 Notice D'utilisation

eng
● The machine is operated by a safety foot switch with emergency stop in
inching mode. If you cannot see the danger area constituted by the revolving
workpiece from the operating point, set up protective measures, e.g. cordons.
There is a risk of injury.
● Only use the machine for the intended purpose described in 1. Technical
Data. Work such as roping, assembling and disassembling, thread cutting with
manual die stocks, work with manual pipe cutters as well as holding workpieces
by hand instead of with material supports are prohibited when the machine is
running. There is a risk of injury.
● If the risk of bending and uncontrolled lashing of the workpieces is to be
expected (depending on the length and cross section of the material and
the speed of rotation) or the machine is not standing stably enough, suffi -
cient numbers of height adjustable material supports ROLLER'S Assistent
3B (accessory, Art. No. 120120) must be used. There is a risk of injury if you
fail to do so.
● Never reach into the revolving clamping or guide chuck. There is a risk of
injury.
● Clamp short pipe sections only with ROLLER'S Nipparo or ROLLER'S
Spannfi x. Machine and/or tools can be damaged.
● Thread cutting materials in spray cans (ROLLER'S Smaragdol, ROLLER'S
Rubinol) contains environmentally friendly but highly infl ammable propel-
lant gas (butane). Aerosol cans are pressurised; do not open by force.
Protect them against direct sunlight and temperatures above 50°C. The
aerosol cans can burst, risk of injury.
● Avoid intensive skin contact with the coolant-lubricants. These have a
degreasing effect. A skin protector with a greasing effect must be applied.
● Never let the machine operate unattended. Switch off the machine during
longer work breaks, pull out the mains plug. Electrical devices can cause
hazards which lead to material damage or injury when left unattended.
● Only allow trained persons to use the machine. Apprentices may only use
the machine when they are over 16, when this is necessary for their training and
when they are supervised by a trained operative.
● Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the machine
safely may not use this machine without supervision or instruction by a
responsible person. Otherwise there is a risk of operating errors and injuries.
● Check the power cable of the electric al device and extension leads regularly
for damage. Have these renewed by qualifi ed experts or an authorised ROLLER
customer service workshop in case of damage.

1. Technical Data

Use for the intended purpose
WARNING
Use ROLLER'S Robot thread cutting machines (type 340004, 340005, 340006, 380010, 380011, 380012) for the intended purpose of thread cutting, cutting off, removing
burr, cutting nipples and roller grooves. All other uses are not for the intended purpose and are therefore prohibited.

1.1. Scope of Supply

ROLLER'S Robot 2 / 2 L: ROLLER'S Robot 2 / 2 L: ROLLER'S Robot 2 / 2 L:
ROLLER'S Robot 3 / 3 L (R 2½ – 3"):
ROLLER'S Robot 4 / 4 L (R 2½ – 4"):
Equipped if necessary with additional tool set (¹/ Equipped if necessary with additional tool set (¹/ ) ⅛ – 2" with ROLLER dies R ½ – ¾" and R 1 – 2". Equipped if necessary with additional tool set (¹/
1.2. Article Numbers
Subframe
Wheel set with material rest
Subframe, mobile and folding
Subframe, mobile, with material rest
Dies
Universal automatic
die head ¹/ – 2" die head ¹/ die head ¹/
16 16
Universal automatic
die head 2½ – 3"
Universal automatic
die head 2½ – 4"
Tool set ¹/ – 2" Tool set ¹/ Tool set ¹/ – 2"
16 16 16 16
ROLLER'S cutting wheel St ⅛ – 4", S 8
ROLLER'S cutting wheel St 1 – 4", S 12
Thread-cutting materials
Nippelhalter
ROLLER'S Assistent 3B
ROLLER'S Assistent WB
ROLLER'S Assistent XL 12"
ROLLER'S roller groove device
Clamping sleeve
Changeover valve
Machine cleaner
● Only use approved and appropriately marked extension leads with a suffi -
● Do not dispose of thread-cutting material undiluted in the drain system,
Explanation of symbols
NOTICE
Thread cutting machine, tool set (¹/ ) ⅛ – 2", ROLLER dies R ½ – ¾" and R 1 – 2", oil tray, chip tray, Thread cutting machine, tool set (¹/ Thread cutting machine, tool set (¹/
operating instructions.
Thread cutting machine, tool set 2½ – 3", ROLLER dies R 2½ – 3", oil tray, chip tray, operating instructions.
Thread cutting machine, tool set 2½ – 4", ROLLER dies R 2½ – 4", oil tray, chip tray, operating instructions.
) ⅛ – 2" with ROLLER dies R ½ – ¾" and R 1 – 2".
16 16 16 16
Robot 2 Type U
Robot 2 Type K
Robot 2 Type D
344105
344120
344150
344100
see ROLLER catalogue
341000
340100 340100
341614
see ROLLER catalogue
see ROLLER catalogue
120120
120130
120125
347000
343001
342080
140119
cient cable cross-section. Use extension leads with a cable cross-section of
at least 2.5 mm².
NOTICE
ground water or ground. Unused thread-cutting material should be handed in
to responsible disposal companies. Waste code for thread-cutting materials
containing mineral oil (ROLLER'S Smaragdol) 54401, for synthetic materials
(ROLLER'S Rubinol) 54109. Observe the national regulations.
WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use eye protection
Use ear protection
Power tool complies with protection class I
Power tool complies with protection class II
Environmentally friendly disposal
CE conformity mark
) ⅛ – 2", ROLLER dies R ½ – ¾" and R 1 – 2", oil tray, chip tray,
16 16 16 16
Robot 3 Type U
Robot 3 Type K
Robot 3 Type D
344105
344120
344150
344100
see ROLLER catalogue
341000
381050
381000
340100 340100
341614
381622
see ROLLER catalogue
see ROLLER catalogue
120120
120130
120125
347000
343001
342080
140119
eng
Robot 4 Type U
Robot 4 Type K
Robot 4 Type D
344105
344120
344150
344100
see ROLLER catalogue
341000
381000
341000 341000
341614
381622
see ROLLER catalogue
see ROLLER catalogue
120120
120130
120125
347000
343001
342080
140119
11