Monacor International AXC-2812DV Mode D'emploi page 5

Menu line Selection/ Submenu
1. LENS MANUAL
2. EXPOSURE ↲
1. SHUTTER
2. AGC
OFF
1. SENS-UP
3. SENSE-UP
AUTO ↲ RET ↲
2. RETURN *
SAVE&END ↲
4. BRIGHTNESS
OFF
ON ↲
5. D-WDR 1. LEVEL
AUTO
OFF
1. POS / SIZE ↲
6. DEFOG
AUTO ↲
2. GRADATION
3. DEFAULT ↲
3. BACKLIGHT
OFF
BLC ↲
1. LEVEL
2. AREA ↲
brightening of
3. DEFAULT ↲
areas
1. SELECT
ON ↲
2. DISPLAY
OFF
HSBLC ↲
3. BLACK MASK
blackening of
4. LEVEL
brightest areas
NIGHT ↲
1. AGC LEVEL
5. MODE
ALL DAY
6. DEFAULT ↲
4. WHITE BAL
ATW
AWB
AWC  SET ↲
INDOOR
OUTDOOR
1. BLUE
MANUAL ↲
2. RED
5. DAY&NIGHT – day/night mode (switching between colour mode and B/ W mode)
EXT ↲ – switching
1. D  N (DELAY)
via brightness sensor 2. N  D (DELAY)
1. D  N (AGC)
AUTO ↲ – switching
2. D  N (DELAY)
via brightness of image
3. N  D (AGC)
4. N  D (DELAY)
COLOR
1. BURST
B / W ↲
1. LEVEL
ON ↲
2. IR
B/W mode 2. AREA
SMART
OFF
1. 2DNR
6. NR ↲ – noise reduction
2. 3DNR
Options in bold = factory setting *The line RETURN with the options RET and SAVE&END is available in all submenus.
1 only available if for EXPOSURE \ SHUTTER = AUTO or 1/25 is selected and EXPOSURE \ AGC > 0
2 Setting of an area:
1) When POSITION is displayed, use  , , ,  to define the position of the area in the image and confirm with "IRIS +".
2) For SIZE, use  , , ,  to define the size of the area and confirm with "IRIS +".
, 
3) Use to define if the setting is terminated (RET) or if the position or size is to be changed (AGAIN) and confirm with "IRIS +".
Setting; function
fixed lens
AUTO = automatic exposure
1/25, 1⁄50, FLK (= 1⁄100), 1/200 ... 1⁄50 000, x 2, x 4, x 6 ... x 30 = fixed exposure time [s]
0 ... 13 ... 15 = gain control range (0 = no gain control)
deactivation of exposure time extension in poor lighting conditions
x 2 ... x 4 ... x 30 = exposure time extension in poor lighting conditions
return to higher menu level
save settings and exit the menu
1 ... 40 ... 100
deactivation of wide dynamic range
0 ... 5 ... 8 = wide dynamic range level
automatic definition of wide dynamic range level
deactivation of contrast enhancement for blurred images (e. g. due to fog)
definition of position/size
2
0 ... 2 = level of contrast enhancement
reset of all settings of this submenu to the factory settings
no backlight compensation
LOW, MIDDLE, HIGH – brightening level
definition of area to be brightened 2
reset of all settings of this submenu to the factory settings
AREA 1 ... 4 – area selection
definition and activation of area selected 2
deactivation of area selected
ON, OFF – blackening of brightest areas on/off
1 ... 90 ... 100 = threshold value for blackening brightest areas
0 ... 48 ... 255 = threshold value (HSBLC only active in poor lighting conditions)
HSBLC always active
reset of all settings of this submenu to the factory settings
automatic white balance
automatic white balance with deviating colour temperature range
semi-automatic white balance: At the place of installation, hold a white object
(e. g. sheet of paper) in front of the camera and send the command "IRIS+".
The camera will perform a white balance.
white balance for indoor applications
white balance for outdoor applications
0 ... 48 ... 100 = blue colour correction for manual white balance
0 ... 45 ... 100 = red colour correction for manual white balance
0 ... 60 = delay for automatic day ➾ night switching
0 ... 60 = delay for automatic night ➾ day switching
1 ... 200 ... 255 = threshold value for day ➾ night switching
0 ... 60 = delay for day ➾ night switching
1 ... 80 ... 255 = threshold value for night ➾ day switching
0 ... 60 = delay for night ➾ day switching
ON, OFF – colour synchronization signal (only if necessary for synchronizing the monitor)
0 ... 15 = compensation of overexposure by IR LEDs at close range
definition of corresponding area
2
deactivation of function
OFF, LOW, MIDDLE, HIGH – 2D-noise reduction
OFF, LOW, MIDDLE, HIGH – 3D-noise reduction
Menu line Selection/ Submenu
7. SPECIAL ↲ – special functions
OFF
1. CAM TITLE
ON ↲
1. FREEZE
1
2. D-EFFECT 2. MIRROR
3. NEG. IMAGE
OFF
1. SELECT
2. DISPLAY
3. SENSITIVITY
3. MOTION
4. COLOR
Motion
ON ↲
5. TRANS
detection
6. ALARM ↲
7. DEFAULT ↲
OFF
1. SELECT
4. PRIVACY
2. DISPLAY
Masking of
ON ↲
areas
3. COLOR
4. TRANS
5. DEFAULT ↲
5. LANGUAGE
OFF
1. LIVE
ON ↲
DPC
OFF
6. DEFECT ↲
2. WHITE
ON ↲
DPC
Defective
pixel compen-
sation
OFF
3. BLACK
ON ↲
DPC
7. RS485 ↲
8. ADJUST ↲
1. LEVEL
AUTO ↲
2. START AGC
1. SHARPNESS
3. END AGC
OFF
1. GAMMA
LCD ↲
2. BLUE GAIN
2. MONITOR 3. RED GAIN
1. BLUE GAIN
CRT ↲
2. RED GAIN
3. LSC
4. VIDEO OUT.
SAVE&END ↲
RESET ↲
9. EXIT
NOT SAVE ↲
Setting; function
camera name not displayed
To enter the camera name to be displayed, select a character or a function and
confirm.
 – previous position or next position; CLR – clear name
POS – definition of the position of the camera name; END – return to menu SPECIAL
ON, OFF – "freezing" of image (still image)
MIRROR, V-FLIP, ROTATE, OFF – horizontal /vertical mirror image or image rotation
ON, OFF – negative image
deactivation of motion detection
AREA 1 ... 4 – area selection
ON ↲
definition and activation of detection area selected
OFF deactivation of area selected
1 ... 80 ... 100
GREEN, BLUE, WHITE, RED – marking colour
1.00, 0.75, 0.25, 0.00 – transparency of marking
1. VIEW TYPE ALL, OFF, BLOCK, OUTLINE – type of marking
2. OSD VIEW ON, OFF – insertion "MOTION DETECTED"
3. ALARM OUT. ON, OFF – without function (no alarm output available)
4. TIME 0 ... 3 ... 15 = display time
reset of all settings of this submenu to the factory settings
deactivation of privacy masking
AREA 1 ... 4 – area selection
OFF deactivation of area selected
MOSAIC ↲
mosaic effect, definition of area 2
INV. ↲
negative effect, definition of area 2
COLOR ↲
colour mask, definition of area
2
WHITE, BLACK, RED, BLUE, YELLOW, GREEN, CYAN, USER – masking colour
0.25, 0.50, 0.75, 1.00 – transparency of mask
reset of all settings of this submenu to the factory settings
ENG↲, GER↲, FRA↲, ITA↲, SPA↲, POL↲, RUS↲, POR↲, NED ↲, TUR ↲, HEB ↲, ARB ↲, ...
deactivation of permanent automatic defective pixel compensation
1. AGC LEVEL 0 ... 30 ... 255 = AGC threshold
2. LEVEL 0 ... 16 ... 100 = sensitivity
deactivation of semi-automatic compensation of hot pixels
1. POS / SIZE ↲
definition of position/size 2
2. START ↲
start of automatic compensation of hot pixels
ON, OFF – black image (to improve visibility of defective pixels)
3. DPC VIEW
4. LEVEL 0 ... 4 ... 100 = sensitivity
5. AGC 0 ... 13, 14 = AGC threshold
6. SENS-UP x 2 ... x 6 ... x 30 = extension of exposure time
deactivation of semi-automatic compensation of dead pixels
1. POS / SIZE ↲
definition of position/size 2
2. START ↲
start of automatic compensation of dead pixels
ON, OFF – white image (to improve visibility of defective pixels)
3. DPC VIEW
4. LEVEL 0 ... 100 = sensitivity
without function (interface not available)
0 ... 5 ... 10 = level of automatic sharpness correction
0 ... 64 ... 255 = start value for sharpness correction
0 ... 140 ... 255 = end value for sharpness correction
deactivation of automatic sharpness correction
USER, 0.45, 0.50, 0.55 ... 1.00 = exponent for gamma correction
0 ... 50 ... 100
0 ... 50 ... 100
0 ... 50 ... 100
0 ... 50 ... 100
ON, OFF – lens shading correction at the edges of the image
PAL, NTSC; ⚠ do not change (may result in image loss)!
save settings and exit the OSD menu
reset to factory settings (without saving settings)
exit the OSD menu without saving any changes
2