Montage van stanghouder en spiegel
1. Controleer of de stanghouder op uw autospiegel geplaatst kan worden;
2. De stanghouder (b) tegen de achterkant van het spiegelhuis van uw auto houden;
3. Draai de stelschroeven voor strippen en stang (c) bijna geheel los;
4. De 2 lange strips (d) voor montage aan de bovenzijde van de spiegel door de daarvoor
bestemde sleuven in de stanghouder schuiven. Voorzie deze van bijgevoegde zuignap-
pen en haak deze in aan de voorzijde van de autospiegel;
5. Gebruik voor bevestiging aan de onderzijde de strip met de lange of de korte haak (f,g)
(afhankelijk van uw autospiegel); haak deze aan de stanghouder bevestigde korte strip.
Bevestig desgewenst een zuignap. Draai de verticale stelschroef nu voorzichtig aan (c);
6. Controleer of alle zuignappen op de juiste plaats zitten;
7. Zorg ervoor dat de stanghouder en de bevestigingsstrips zo vlak mogelijk tegen de
spiegel aan liggen voor maximale stabiliteit.
8. Indien spiegel en huis goed zijn geplaatst, kunt u de stelschroef voor de strippen definitief
aandraaien (c). ZORG ERVOOR DE STELSCHROEVEN NIET TE OVERBELASTEN.
9. Indien de stanghouder correct gemonteerd is, kunt u de stang met spiegelkop (a) mon-
teren en deze op de juiste positie instellen.
Zorg ervoor dat de spiegel behuizing zo geplaatst wordt zodat alle instellingen bruikbaar
zijn, zowel verticaal als horizontaal.
De afstandsbediening
Met de afstandsbediening kunt u uw spiegels in 4 posities programmeren: links verticaal (1),
rechts verticaal (2), links horizontaal (3) en rechts horizontaal (4). De standaardinstelling is
links horizontaal (3). Indien u een van de andere posities wenst, dient u de spiegel eerst te
programmeren. (zie Programmeren en instellen van de Mirror Control
Let op de positie van de spiegel infrarood sensor!
1
MIRROR
3
).
®
CONTROL
Programming and setting the Mirror Control
1. First mount the mirror manually in the prefered orientation (left, right/vertical, horizontal)
on your car mirror. Look at the position of the infrared sensor! In both vertical positions
the sensor (h) should be visible on the top of the Mirror Control
postions - on the outside of the Mirror Control
2. Take a comfortable position behind the stearing wheel;
3. Press for 2 seconds the P-button (program) on the remote control and release (5);
4. Within 2 seconds press one of the 4 buttons according to the position of your mirror
(see Remote control basic);
5. If it's correct you will get a confirmation - mirror nods (1 second up - 1 second down),
Movements in other directions indicate wrong settings, start again;
6. The last step is to set the most suitable view by using the same 4 buttons (see below).
MIRROR
CONTROL
up
down
left
right
P
P
5
Replacing the mirror batteries (6)
1. On the back of the mirror is a cover under which is a 9V battery;
2. Unscrew the holding screw with a suitable screwdriver. Keep it in your car!
3. By using the screwdriver remove the cover and release the battery holder;
4. Change the battery, making sure that it's correctly positioned;
5. Press and screw the cover back.
2
After replacing the mirror battery the Mirror Control
programming (left, horizontal). Other positions have to be programmed again.
Replacing the remote control batteries (7)
1. On the back of the remote is a cover under which there are two 1.5 V batteries;
2. Press the cover open to replace the batteries;
3. Make sure that they are correctly positioned;
4. Press the cover back on.
Replacing the remote control batteries has no ifluence on the last mirror position.
4
-
In cold conditions batteries run down quicker.
-
The capacity (mAh) of rechargeable batteries is less than
non-rechargeable batteries. We advise non-rechargeable batteries.
®
®
, in both horizontal
(see Remote control basic)
®
Troubleshooting
If your remote control fails to operate:
• Check if it's correctly programmed.
• If necessary replace the remote control batteries.
• If necessary replace the Mirror Control battery.
• Press the mirror glas (by hand) in an other position and
try again.
If the remote still fails to operate, consult your supplier.
©
unit starts in default
Store in a dry place
English
6
7