Operation - Windsor Saber Blade 16 Mode D'emploi

Operation

Note
To take the brush drive out of opera-
tion, immediately release brush drive
switch.
Chemical filling
Warning
Risk of damage. Only use the recom-
mended detergents. With respect to
different detergents the operator bears
the increased risk regarding the opera-
tional safety and danger of accident.
Only use detergents that are free from
solvents, hydrochloric acid and hydrof-
luoric acid.
Note
Do not use highly foaming detergents.
Observe the meter mixing notes.
Recommended detergents:
Open the cover of the solution tank.
Pour in water/detergent mixture.
Maximum temperature of the liquid
120°F (50°C)
Note
The solution tank cover can be used to
meter the detergent. The capacity of
the cover up to the mark represents 1%
of the fresh water reservoir capacity.
Close the cover of the solution tank.
Driving to the Place of Use
Short distances on even surfaces
Place the slider vertically.
Position the rotary handle for the
brush contact pressure in the drive
position.
Use the pushing handle to push the
appliance to the place of use.
Longer distances on uneven surfac-
es
Place the slider vertically and tilt the
lock up.
Install the transport wheels.
Tilt the appliance to the side and
drive it to the place of use on its
transport wheels.
If the transport wheels hinder the use of
the appliance:
Press the transport wheel release
button and pull the transport wheel
out.
Insert the transport wheels into their
holder until they stop.
Adjust the brush contact pres-
sure
Place the slider vertically.
Adjust the rotary handle of the
brush contact pressure to the de-
sired value.
6
English
Note
Carry out the initial cleaning attempts
with less contact pressure. Increase
contact pressure step-by-step until the
desired cleaning result is achieved. A
correct setting of the contact pressure
reduces the wear and tear of the brush-
es.
The brush drive is switched off when
there is overload.
When cleaning with microfibre rollers,
the contact pressure must not be ad-
justed higher than the position men-
tioned below. With a higher contact
pressure, there is a danger of destroy-
ing the microfibre rollers.
+
-
Establish mains contact
Danger
Check the mains cables of the machine
each time before using the machine to
see that it is not damaged. Never op-
erate a machine with damaged cables.
Get the damaged cables replaced by
an electrician.
Insert the looped end of the exten-
sion cable in the strain relief hook.
Plug in the mains plug.
Cleaning
If the detergent solution is to be vac-
uumed off after the cleaning pro-
cess, use squeegee lowering pedal.
Swivel the slider toward the opera-
tor - the chassis is retracted and the
brushes touch the floor.
Turn on the brushes by using the
switch for the brush drive.
Turn on the brush irrigation by using
the switch for the detergent solu-
tion.
Move the appliance over the sur-
face to be processed by the slider.
Warning!
Risk of damage to the floor covering.
Do not operate the appliance on the
spot.
Polishing
Swivel the slider toward the opera-
tor - the chassis is retracted and the
brushes touch the floor.
Turn on the brushes by using the
switch for the brush drive.
Move the appliance over the sur-
face to be processed by the slider.
Warning!
Risk of damage to the floor covering.
Do not operate the appliance on the
spot.
Note
To polish under furniture, remove the
solution tank and recovery tank.
Shutting Down the Appliance
Release the switch for detergent so-
lution.
Push the appliance forward for an-
other 3-6 ft (1-2 m) to draw off resid-
ual water.
Release the brush drive button.
Press the pedal to lower the vacu-
um bar.
Place the slider vertically - the
brushes are elevated.
Disconnect the mains plug.
Warning
Danger of deforming the brushes.
When switching off the appliance, take
the load off the appliance by placing
the slider vertically.
Emptying the Solution tank
Open the locks for the Solution
tank.
Tilt the carrying handle for the re-
covery tank towards the side.
Lift up the solution tank and carry it
to the disposal site.
Warning
Please observe the local provisions re-
garding the wastewater treatment.
Remove the cover of the solution
tank and pour out the liquid via the
notch.