Installation Instructions - Novoferm tormatic Novomatic 200 Manuel D'utilisation

• Installation Instructions

Preparing for installation
1. In order to allow mains connection, a socket
must be available on site - the supplied mains
connecting cable has a length of 80 cm.
2. Check the stability of the door. Retighten the
screws and nuts on the door.
3. Check if the door is running smoothly. Lubricate
shafts and bearings. Check the petension of the
springs and if necessary re-adjust.
4. Establish the door's highest point of travel (see
figure 6).
5. Close the door and disable any existing locks
out of operation, if necessary dismantle.
6. For garages without a second entrance, an
emergency release is required (accessory).
7. If a wicket pass door is included, fit the wicket
door contact.
1
The following tools are required
- Drilling machine with drill
- Metal saw
- Spanner, 13 mm
- Slotted screwdriver, width 3 mm
- Phillips screwdriver, size 2 x 100
- Spirit level
- Tong
Attention: Check the screws and wall plugs prior to
use to ensure that these are suitable for the strctural
conditions on site.
2
Supply package = complete set
1 - Operator head including
40 W light bulb, socket E14
2 - Chain sprocket
3 - Track, operator side
4 - Carriage
5 - Chain
6 - Deflection roller
7 - Connector
8 - Track, door side
9 - Tensioner
10 - Wall bracket
11 - Linking bar
12 - Bag of screws
13 - Support straps
13 - Hand transmitter
14 - Internal push button
3
Track
Build together the track as shown in images 3a and
3f.
4
Fastening the track to operator head
Slot track with chain sprocket onto the operator shaft
and screw down with the 4 screws (8x16).
5
Attaching the wall bracket
In order to ensure that the door can run freely
underneath the track, distance "x" must be greater
than 20 mm. Choose distance "x" so that the angle of
the linking bar does not exceed 45° (see figure 11).
Mark the door's highest point of travel "a" plus
distance "x" on the lintel.
Hold wall fastening (10) at the total height ("a" + "x")
vertically over the door connector attachment drill
and mark the position for the holes. Drill holes for wall
plugs and screw the wall bracket onto the wall.
6
Support straps
Positioning the prefitted operator at an angle to the
door, screw to wall bracket (10). Lift up operator,
making sure that it cannot fall down, and align in such
a way that the track runs horizontal and parallel
between the door tracks.
Retain these installation, operating and maintenance instructions for the full duration of the operator's service life!
Establish the length of the support straps for the
operator head and the central support. If
necessary, shorten using a saw, and then screw in
place.
Note: Before starting any drilling, cover
over track and operator head to protect
them from drilling dust.
7a
Fitting the connector attachment
The enclosed door connector attachment is suitable
for all Novoferm up-and-over doors and Novoferm
ISO20 sectional doors.
Position door connector attachment (16) centrally on
the top edge of the door leaf.
Mark fixing holes and drill using 4 mm metal drill
(max. Drilling depth 10 mm) or use the existing drill
holes. Screw on attachment using enclosed self-
tapping screws 6.3 x 16 (4 - 6 screws up-and-over
door, 6 screws - ISO20).
7b
For other sectional doors, use telescopic fitting
(17) (accessory).
7c
Connecting the door connector attachment
to the carriage
Place linking bar (11) between carriage (4) and the
door connector attachment and connect at both ends
with the bolts. Provide bolts with security clips. Attach
security clips to bolts.
8
Disengaging the carriage
In order to carry out further work, it may be necessary
to disconnect the operator from the door by pulling
the pull cord on carriage (4) and move the door
manually.
Note: If the door is to be operated manually for a
longer period of time, then the locking pin must be
removed from parking position (a) on the left and with
theopull cord in locking position (b).
In order to relock, return the locking pin into the
parking position (a) on the left and restore the
connection between the operator and the door. On
the next movement, the carriage automatically re-
engages.
9
Aligning the aerial / Connecting plan
Note:
It is essential to pull out the mains plug
before opening the cover!
Do not connect any live leads, only connect
potential-free buttons and potential-free
relay outputs. Finally, replace the cover and
screw down.
Before using the operator for the first
time, it must be tested to make sure that it
is working properly and safely (see
section on Maintenance/Checks).
E. Connecting the aerial
Route the aerial on the housing exit upwards.
When using an external aerial, the shielding
must be assigned to the adjacent terminal (F, on
right) 9.
F. Connection for external impulse generator
(accessory, e. g. key switch or digital coder ) 9b.
• Programming the operator
10
Control elements
The controls for programming the door operator are
protected by a transparent cover. The transparent
cover can be opened with a screwdriver. After the
operator has been programmed, the transparent
cover must be closed again.
A . Numerical display shows the menu stage as well
as the selected value.
a. Point display, lights up to indicate "ready for
13
operation" and flashes on the hand transmitter
code learning completion.
B . Button during the setting / adjustment phase
serves as an "up" button and outside the menu as
a start button.
C . Button during the setting /adjustment phase
serves as a "down" button.
D . Button is used to call up the setting/adjustment
menu, to change the menu stages and to store the
settings.
The programming of the control unit is menu-driven.
By pressing button , the menu guide is called up.
The numbers displayed indicate the menu stage.
After approx. 2 seconds, the display flashes and the
setting can be altered via buttons
selected setting is stored with button
programme jumps automatically to the next menu
stage. By repeatedly pressing button
stages can be skipped. To quit the menu, press
button until "0" is shown again. Outside the menu,
button can be used to generate a start impulse.
Before programming
- Allow door to engage into the carriage.
- Pull out the mains plug. Point display (a) lights up.
- Make sure that the aerial is correctly positioned
(see figure 9).
- Observe the hand transmitter instructions.
11
Menu stage 1: Programming the start
function for the hand transmitter
Briefly press button . "1" is displayed. As soon
as the display flashes, press and keep pressed for
approx. 1 second the button of the hand
transmitter. As soon as the code has been read,
the red point display (a) flashes five times before
quitting.
After the code has been learned, briefly press
button .
"0" appears indicating that you have come to the end
of the menu.
Deleating all the hand transmitters programmed
for the operator:
Plug in the operator's main plug while pressing
button .
12
Menu stage 3: Setting / adjusting the top
end-of-travel position
Keep button pressed for 3 seconds. Number 3
appears in the display. Wait a short while until the 3
starts flashing. Press button and make sure that
the door travels in the OPEN direction. By pressing
button , the position can be corrected into direction
CLOSE.
Once the desired OPEN end-of-travel position has
been reached, press button . The operator stores
the OPEN end-of-travel position and "4" appears in
the display.
GB
and . The
. And the
, menu