Publicité
Les langues disponibles
Les langues disponibles
HCW-4 36 mm Box-End
Wrench and Pin Spanner
The HCW-4 is a double-ended
wrench used to remove, install
and
adjust
adjustable-type
bottom brackets.
The 36mm
box end wrench fits most fixed
(drive side) cups and the pin
spanner fits most adjusting
(non-drive side) cups.
HCW-5 Lockring Wrench
The HCW-5 is a double-ended wrench designed
to remove, install, and adjust the lockring on
most adjustable-type bottom brackets.
HCW-15 32mm and 36mm
Headset Wrench
The HCW-15 is a double-ended wrench used
when adjusting most threaded-type headsets.
HHP-2 Bearing Cup Press
The HHP-2 accurately aligns
and presses 1", 1-1/8", 1-1/4",
and 1.5" headset cups. In
addition, it presses cartridge
bearings and cups into one-
piece bottom bracket shells
and holds fixed cup wrenches
firmly in place when removing or
installing adjustable-type bottom
brackets. See information sheet
packaged with tool for complete
instructions.
HMR-4 Shop Hammer
HT-8 8mm Hex Tool
The HT-8 is used on pedals that require an 8mm
hex wrench for removal and installation. It also
is used for removal and installation of 8mm
socket head crank bolts.
NP-6 Needle Nose Pliers
The NP-6 is a professional quality needle nose
pliers for grabbing cables, extracting debris from
tires, and other grasping and crimping tasks.
OBW-4 Offset Brake Wrench
The OBW-4 is a thin offset wrench
with 10, 11, 12 and 13mm openings
to fit the centering flats, pivot nuts
and lock nuts on many dual pivot
and side pull brake calipers.
PAW-12 Adjustable Wrench
The PAW-12 is a heavy duty 12" adjustable
wrench that opens to 36mm for use when
adjusting headsets or when removing freewheels
or cassette lockrings.
PH-1 P-Handled Hex Wrench Set
Designed to install and adjust brakes, derailleurs,
saddles, seat posts, handlebars, stems, water
bottle cages, etc. The long shaft of each wrench
is fitted with a Bondhus balldriver for hard to
reach bolt heads. The short shaft is straight, for
fully tightening bolts in high torque applications.
PPL-1 PolyLube 1000
Polylube 1000 is a high performance
polyurea grease specially formulated
for
use
with
headsets,
bottom brackets, and other bicycle
components.
PW-4 Pedal Wrench
A pedal wrench is necessary for removing and
installing pedals for replacement, service, or
packing a bike for shipment.
Instructions:
Pedal Removal:
1. Shift chain to largest chainring. This
helps protect hands and arms from sharp
chainring teeth.
2. Place PW-4 on right pedal. Holding left
crank for leverage, turn PW-4 counter-
clockwise until pedal is removed.
3. Place PW-4 on left pedal. Holding right
crank for leverage, turn PW-4 clockwise
until pedal is removed.
Pedal Installation:
1. Apply grease to threads of both pedals.
2. Thread right pedal (marked "R") clockwise
into right crank by hand. Tighten with PW-4.
3. Thread left pedal (marked "L") counter-
clockwise into left crank by hand. Tighten
with PW-4.
RT-1 Head Cup Remover
The RT-1 makes headset cup
removal easy. The tool is pulled
through the frame until the flared
ends snap in behind the cup. A
blow on the tool head removes
the cup. Fits 1", 1-1/8", 1-1/4"
as well as some low profile and
internal head cups.
SBC-1 Spoke, Bearing, & Cotter Gauge
This handy shop aid is ideal for sizing spokes,
ball bearings and crank cotters.
SCW Shop Cone Wrenches(13mm to 19mm)
Park Tool Shop Cone Wrenches are designed to
fit the narrow wrench flats on hub adjustment
cones and locknuts when disassembling, as-
sembling, and adjusting wheel hubs.
hubs,
SD-0, SD-2, SD-3, and SD-6
Shop Screwdrivers
Durable and comfortable, shop quality Park Tool
screwdrivers are used for adjusting derailleurs,
brakes, and a variety of accessories.
SD-0 #0 Phillips Head
SD-2 #2 Phillips Head
SD-3 3mm Straight Blade
SD-6 6mm Straight Blade
Publicité
