Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Installing the Radial-Shape Select Havahart
Placing Training Flags:
Once your Boundary is established, it' s time to place the remaining
Training Flags. Training Flags are critical for the effective training of
your dog.
NOTE : Consult the Flag Calculator on Page 7 to determine the
number of Flags you need.
1.
Repeat the process in Step 3 of Establishing the Fence
Boundary/Trigger Zone Distance by walking toward the Fence
Boundary about 6 feet (2 paces) to the right of the previous
Flag, verifying the Fence Boundary, placing a Flag, and then
stepping back into the Roaming Area.
2.
Repeat Step 1 until the entire containment area is surrounded
(see Illustration D).
NOTE: These Flags represent the location of your Wireless
Fence and will be used later to train your dog. Be sure that
the Flags form an enclosed area and that your dog has safe,
adequate entry to your house.
Turning the Trigger Zone Off/On:
1.
Navigate to the Menu where Setup Menu and Display Options
are listed (see Screen 2.0).
2.
Press the blue flashing Power Button to Turn Off the Trigger
Zone (see Figure 1.6).
3.
Press the Power Button again to Turn On the Trigger Zone.
NOTE: All settings will be retained in system memory
when you Turn Off the System.
If you would like to confirm that the Havahart
Wireless Collar
®
will deliver a Static correction when crossing the Trigger Zone,
you can use the Heart-Shaped Collar Tester. Set the correction
level to Static Level 1. Hold the metal contact points located
inside the holes of the Heart-Shaped Collar Tester against
the Probes of the Havahart
Wireless Collar so that metal is
®
touching metal. Carry the Havahart
Wireless Collar by the
®
Battery Housing with the Heart-Shaped Collar Tester held
against the Probes. Extend your arm down by your side. Make
sure that your body does not get between the Collar and the
Controller as your body may affect the signal and cause the
Boundary to shift inward. Walk to a Boundary point and watch
the Heart-Shaped Collar Tester illuminate. Remember to set
the correction level back to Tone-Only for training.
15
www.HavahartWireless.com
Wireless Dog Fence
®
Illustration D
Screen 2.0
Power
Power Button
Figure 1.6
Installing the Radial-Shape Select Havahart
Display Options:
Viewing Distance to Dog and Battery Status
(see Screen 2.3):
Select Display Options (see Screen 2.1).
•
Select Show Collar Monitor (see Screen 2.2).
•
NOTE: See Battery Status Level meanings on Page 13.
Turning the Display Off/On
(see Screen 2.2):
Select Display Options (see Screen 2.1).
•
Select Display Off (see Screen 2.2).
•
Press Enter to turn the display back on.
•
NOTE: Turning off the display will NOT turn off the System.
Setting Alarm Options:
Setting Alarm Volume Level (see Screen 2.5):
Select Display Options (see Screen 2.1).
•
Select Alarm Options (see Screen 2.2).
•
Select Alarm Volume Level (see Screen 2.4).
•
Use the up or down arrow keys to choose the desired alarm
•
level. Select HIGH, LOW, or OFF (see Screen 2.5).
Press Enter.
•
Select OK to save.
•
NOTE: It is recommended to set the alarm volume level to HIGH.
Turning Boundary Breach Alert Off/On
(see Screen 2.6):
Select Display Options (see Screen 2.1).
•
Select Alarm Options (see Screen 2.2).
•
Select Boundary Breach (see Screen 2.4).
•
Use the up or down arrow keys to turn the boundary breach
•
alert OFF or ON (see Screen 2.6).
Press Enter.
•
Select OK to save.
•
NOTE: It is recommended to keep the Boundary Breach Alert ON.
Wireless Dog Fence
®
Screen 2.1
Screen 2.2
Screen 2.3
Screen 2.4
Screen 2.5
Screen 2.6
16
1-800-800-1819, Option 453
Publicité
Table des Matières
