Télécharger Imprimer la page

Zanussi ZFC 11JE Notice D'utilisation page 11

Publicité

Les langues disponibles

Les langues disponibles

Make sure that the power plug is not squashed or damaged by the back of the fridge/freezer.
- A damaged power plug may overheat and cause a fire.
Do not place heavy articles or the fridge/freezer itself on the power cord.
- There is a risk of a short circuit and fire.
Do not remove the power cord by pulling on its lead, particularly when the fridge/freezer is being pulled out of its
niche.
- Damage to the cord may cause a short-circuit, fire and/or electric shock.
- If the power cord is damaged, it must be replaced by a certified service agent or qualified service personnel.
If the power plug socket is loose, do not insert the power plug.
- There is a risk of electric shock or fire.
REFRIGERANT
Your appliance contains an environmental friendly gas called isobutane (R600a) as refrigerant which is nevertheless flammable.
During transportation and installation of the appliance, be sure that none of the components of the cooling circuit become dam-
aged. If any part of the cooling circuit damaged: avoid naked flames and sources of ignition; thoroughly ventilate the room in which
the appliance is installed.
DISPOSAL
Appliance Packaging Information All materials are environmentally sound! They can be dumped or burned at an incinerating plant
without danger! About the materials: The plastics can be recycled and are identified as follows:
>PE< for polyethylene, e.g. the outer covering and the bags in the interior.
>PS< for polystyrene foam, e.g. the pads, which are all free of chlorofluorocarbon.
The carton parts are made from recycled paper and should be disposed of at a waste-paper recycling collection location. Disposal
of old Appliances For environmental reasons, refrigaration appliances must be disposed of properly. This applies to your old appli-
ance, and -at the end of its service life- for your new appliance as well.
Warning! Before disposing of old appliances make them inoperable. Remove plug from mains, sever the power cable,
remove or destroy any snap or latch closures. This eliminates the danger that playing children lock themselves into the
appliance (danger of suffocation!) or place themselves into other life-endangering situations.
Disposal
The appliance may not be disposed of with domestic waste or bulky refuse. The refrigerating circuit may not be damaged.
Information concerning collection schedules or locations can be obtained from the disposal authorities or town hall.
The symbol on
the product or on its packaging indicates that this product may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this prod-
uct is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this
product, please contact your local city office, your household waste disposal service or the shop where you purchased the prod-
uct.
POSITION
Place the freezer horizontally on a firm surface, resting on all four plastic feet. Use a wooden block or similar object to compensate for any
bumps/holes in the surface. The room should be dry and adequately ventilated. Temperatures of the external environment have an
impact on the energy consumption of the device. Therefore: do not put the device to a place exposed to sunshine ore besides a
radiator or oven, put it to a place where the temperature of the environment corresponds to the climatic classification for which the
device was designed.
Climatic classification
Ambient temperature limits
SN
N
ST
T
If the freezer has been handled standing on end it should be allowed to stand in normal position for about 12 hours before switch-
ing it on. Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown.
ELECTRICAL REQUIREMENTS.
Before switching on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate, located
inside the lid.
Warning: This appliance must be earthed.
this appliance complies with the following EC Directives:
- 73/23/EEC of 19. 02. 1973 - Low-Voltage Directive
- 89/336/EEC of 03. 05. 1989 (including Amendment Directive 92/31/EEC - EMC Directive.
Some of the models are not available in all countries. Testing has been carried out in accordance with ISO 5155 regarding the deter-
mination of freezer capacity, energy consumption and hold-overtime. Information for test institute: A plan of the positioning of test
packages may be obtained directly from the manufacturer.
SWITCHING ON FREEZER BOX
Close top of freezer box installed in accordance with specifications down then connect equipment with mains as specified above.
At this time electric components inside will be energised. Adjust knob of temperature regulator in centre with rotating clockwise.
After a weak clicking cooling compressor will start together with slight vibration and noise.
from +10°C to +32°C
from +16°C to +32°C
from +18°C to +38°C
from +18°C to +43°C
G G B B
11

Publicité

loading