Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
WORM GEAR SPEED REDUCER
INSTRUCTION MANUAL
Item No.: 8494130-8494155-8494171
Introduction
When running the WPS series speed reducer for the first time optimal performance is achieved by a
process of gradually increasing the load, up to full load, over the first 50 hours of use. During these
early stages of running, precautions should be taken to avoid overloading the speed reducer. If the
speed reducer must be run under full load without this break in period it is important to monitor its
operating temperature. If the temperature goes above 107°C (225℉) the speed reducer should be
stopped and allowed to cool. A progressive reduction in temperature will occur over many hours
until the unit has reached its highest efficiency.
Features
• Forged Manganese Bronze Ring Gear
• Induction Hardened, Ground and Polish Worm Gear
• Annealed Cast Iron Housing, Precision Machined for Accurate Shaft Alignment
• Front and Back Input Shaft Ball Bearings
• Tapered Roller Bearings on Output Shaft
• High-Strength, Heat treated Input and Output Shafts
• Precision cast iron housing and bronze gear construction provides strength and durability
• Used as part of the drive unit for conveyors, saw mills, winch drives, elevators, etc
Specifications
SKU No.
Model No.
Ratio
8494130
WPS70B-10-2.0
10:1
8494155
WPS70B-30-2.0
30:1
8494171
WPS70B-60-2.0
60:1
WORM GEAR SPEED REDUCER
INSTRUCTION MANUAL
Specifications
Max. Input HP
2
Max. Torque Output (in-lb)
720
Max. Input Shaft Side Load (lbs)
155
Max. Output Shaft Side Load (lbs)
822
Max. Input Shaft Speed (RPM)
1,800
Efficiency
90%
Max. Input HP
2
Max. Torque Output (in-lb)
880
Max. Input Shaft Side Load (lbs)
63
Max. Output Shaft Side Load (lbs)
1004
Max. Input Shaft Speed (RPM)
1,800
Efficiency
82%
Max. Input HP
2
Max. Torque Output (in-lb)
840
Max. Input Shaft Side Load (lbs)
30
Max. Output Shaft Side Load (lbs)
958
Max. Input Shaft Speed (RPM)
1,800
Efficiency
71%
1 OF 8
Publicité
Manuels Connexes pour Hydroworks WPS70B-10-2.0
Sommaire des Matières pour Hydroworks WPS70B-10-2.0
- Page 1 SKU No. Model No. Ratio Max. Input HP Max. Torque Output (in-lb) Max. Input Shaft Side Load (lbs) 8494130 WPS70B-10-2.0 10:1 Max. Output Shaft Side Load (lbs) Max. Input Shaft Speed (RPM) 1,800 Efficiency Max. Input HP Max. Torque Output (in-lb) Max.
-
Page 2: Installation Dimensions
Oil Sight Glass Hex Head Cap Screw Input Shaft Cap Input Shaft Bearing Gasket Oil Drain Plug Air Vent Model# Ratio Hex Head Cap Screw WPS70B-10-2.0 10:1 WPS70B-30-2.0 30:1 Output Bearing Carrier Cap WPS70B-60-2.0 60:1 O-ring Input Shaft Output Shaft... - Page 3 WORM GEAR SPEED REDUCER WORM GEAR SPEED REDUCER INSTRUCTION MANUAL INSTRUCTION MANUAL 5. The Ring Gear Output Shaft Assembly (#17, 16, 14, 13) can now be removed from the Housing (#22) 1. Leave the protective sleeves on the shafts for safe handling of the speed reducer during Note: Be careful not to nick or scratch the ring gear or output shaft installation.
- Page 4 WORM GEAR SPEED REDUCER WORM GEAR SPEED REDUCER INSTRUCTION MANUAL INSTRUCTION MANUAL Installation a. Oil temperature 1.1 Motors and Speed Reducers b. Type of oil WPS series speed reducer are not shipped with oil so they must be filled before use. c.
- Page 5 WORM GEAR SPEED REDUCER INSTRUCTION MANUAL Problem (s) Possible Cause (s) Suggested Solution (s) 1.Improper alignment between 1. Adjust installation position to make all components align the prime mover, speed reducer or operating device 2. Adjust load or replace with a 2.Overloading suitable type of speed reducer 3.Excessive friction of the output...
- Page 6 No. de Modèle Ratio Spécifications Max. Puissance d’entrée Max. Sortie de couple (in-lb) Max. charge latérale de l’arbre d’entrée (lbs) 8494130 WPS70B-10-2.0 10:1 Max. charge latérale de l’arbre de sortie (lbs) 1,800 Max. Vitesse de l’arbre d’entrée (RPM) Efficacité Max. Puissance d’entrée Max.
-
Page 7: Joint Torique
Vis à tête hexagonale Ecrou de l’arbre d’entrée Roulement de l’arbre d’entrée Joint Bouchon de vidange d’huile Event Modèle# Ratio Vis à tête hexagonale WPS70B-10-2.0 10:1 WPS70B-30-2.0 30:1 Ecrou de sortie pour porte-palier WPS70B-60-2.0 60:1 Joint torique Arbre d’entrée Arbre de sortie Modèle#... - Page 8 REDUCTEUR A ROUE ET VIS SANS FIN REDUCTEUR A ROUE ET VIS SANS FIN MANUEL D’UTILISATION MANUEL D’UTILISATION 1. Laissez les manchons de protection sur les arbres pour une manipulation sûre du réducteur lors des rainures de clavetage, de manière que le joint de l’arbre de sortie ne soit pas endommagé (#12). de l’installation.
- Page 9 REDUCTEUR A ROUE ET VIS SANS FIN REDUCTEUR A ROUE ET VIS SANS FIN MANUEL D’UTILISATION MANUEL D’UTILISATION recommandé si nécessaire. - Selon la géométrie de la roue dentée ainsi que des états de fonctionnement, les réducteurs à roue b. Ajoutez par mois deux coups de graisse à l’unité ayant des roulements graissés. et vis sans fin peuvent ou ne peuvent pas refouler.
- Page 10 REDUCTEUR A ROUE ET VIS SANS FIN MANUEL D’UTILISATION Problem (s) Possible Cause (s) Suggested Solution (s) 1.Improper alignment between 1. Adjust installation position to the prime mover, speed reducer make all components align or operating device 2. Adjust load or replace with a 2.Overloading suitable type of speed reducer 3.Lubricate the output shaft oil...