Preparing The Tool - DeWalt DCN681 Traduction De La Notice D'instructions Originale

2. Fully depress nosepiece against the work surface (motor
will start).
3. Pull trigger (staple will drive into work surface).
4. Release trigger.
5. Lift nosepiece off work surface.
6. Repeat steps 2 through 4 for next application.
NOTICE: The contact trip needs to be depressed followed
by a trigger pull for each staple followed by a release of
both the contact trip and trigger after each staple.
Bump Action (Fig. D)
Bump action is intended for rapid stapling on flat, stationary
surfaces and typically most effective for applications that require
driving shorter staples.
When the tool is set in the bump actuation mode, two
methods of tool operation are available: place actuation and
bump actuation.
Slide the selector switch to expose the triple staple icon
To operate the tool using the place actuation method:

WARNING: A staple will be driven each time the trigger is
depressed as long as the contact trip remains depressed.
1. Depress the contact trip against the work surface.
2. Depress the trigger.
To operate the tool using the bump actuation method:
3. Depress the trigger.
4. Push the contact trip against the work surface. As long as
the trigger is depressed, the tool will drive a staple every
time the contact trip is depressed. This allows the user to
drive multiple staples in sequence.

WARNING: Do not keep trigger depressed when tool is not
in use. Keep the trigger lock-off in the locked position when
the tool is not in use.

WARNING: When the tool's motor is running, pulling the
trigger or depressing the contact trip will cause a staple
to be driven.

Preparing the Tool


WARNING: NEVER spray or in any other way apply
lubricants or cleaning solvents inside the tool. This can
seriously affect the life and performance of the tool.
nOTE: The battery pack is not fully charged out of the carton.
Follow instructions outlined (see Charging a Battery).
1. Read the Safety Instruction section of this manual.
2. Wear eye and ear protection.
3. Ensure magazine is empty of all fasteners.
4. Check for smooth and proper operation of contact trip and
pusher assemblies. Do not use tool if either assembly is not
functioning properly. NEVER use a tool that has the contact
trip restrained in the actuated position.
5. Keep tool pointed away from yourself and others.
6. Insert fully charged battery pack.
Using the Trigger Lock-off (Fig. E)

WARNING: To reduce the risk of serious personal injury,
do not keep trigger depressed when tool is not in use. Keep
the trigger lock-off switch LOCKED (Fig. E) when the tool
is not in use.

WARNING: To reduce the risk of serious personal
injury, lock off trigger, disconnect battery pack from
tool and remove staples from magazine before
making adjustments.
Each D WALT stapler is equipped with a trigger lock-off
e
which when pushed to the right as shown in Figure E, prevents
the tool from firing a staple by locking the trigger and bypassing
power to the motor.
When the trigger lock-off is pressed to the left, the tool will be
fully operational. The trigger lock-off should always be locked
off whenever any adjustments are made or when tool is not in
immediate use.
NOTICE: Do not store tool with battery pack installed. To
prevent damage to the pack and to ensure best battery
life, store battery packs out of the tool or charger in a cool,
dry location.
Loading the Tool (Fig. F)
.

WARNING: Keep the tool pointed away from yourself and
others. Serious personal injury may result.

WARNING: Never load staples with the contact trip or
trigger activated. Personal injury may result.

WARNING: Always remove battery pack before loading or
unloading staples. Serious personal injury may result.
1. Press magazine latch
magazine 6 fully.
2. Insert fasteners into the side of magazine; fasteners should
be loaded with head against back of magazine.
3. Close sliding magazine until magazine latch clips snuggly."
Unloading the Tool (Fig. F)

WARNING: The trigger lock-off should always be locked
off whenever any adjustments are made or when tool is
not in use.
1. Press magazine latch
magazine 6 fully.
2. Tip the tool up until the staples slide freely out of the side of
the magazine.
3. Check to ensure no loose staples remain inside magazine.
4. Close sliding magazine fully.
Dryfire Lock Out feature (Fig. A)
Tool is equipped with a dryfire lock out feature to prevent tool
from cycling when there are no fasteners loaded. When no
fasteners are visible in the Fastener Window
running low on fasteners. If this happens, the tool will be locked
out and will not actuate until more staples are loaded. (Refer to
Loading the Tool)
Adjusting Depth (Fig. G)
The depth that the fastener is driven can be adjusted using the
depth adjustment wheel

WARNING: To reduce risk of serious injury from
accidental actuation when attempting to adjust
depth, ALWAYS:
EngLIsh
15 and open sliding
and open sliding
15
16 , the tool is
3 on the side of the tool.
2
37