Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
g) Setting and switching the cycle and pulse program
Only for item nos. 2144023 & 2144025
Cycle program
If two cycles overlap, the cycle with the earliest start time will be selected.
ON
OFF
ein
aus
Program finish:
Program start:
Programm
Programm
7.30 h ON
16.30 h OFF
7.30 h
16.30 h a u s
MENU
OK
+
-
OK
OK
The brightness may fluctuate when lights are controlled using the cycle program. This can be
prevented by reducing the total load of the connected devices or increasing the cycle duration.
Without additional EMC measures, it is not feasible to configure more than 5 switch operations
per minute.
Pulse program
The pulse program delays the time at which the current is switched
1
on or off during a preset switch interval. The delay (pulse length) can
be configured to a duration of 1 to 59 seconds. The
flash when the time switch is running/switching according to the pulse
program. This program is suitable for ventilation systems or rinsing
systems.
Example 1: Switch interval: 07:00 to 17:30, 15 s delay 17:30:15 s
(switch off)
2
Example 2: Switch interval: 07:00 to 17:30, 15 s delay 07:30:15 s
(switch on)
1. Press the MENU button (2) to switch to the pulse menu. Alterna-
MENU
tively, press the + (10) button, and then press again to switch to
the next menu. The
2. Press the - (3) or + (10) button to select a new program
3. Select the pulse duration with the - (3) or + (10) buttons, and
OK
press the ok button (9) to confirm.
+
-
4. To check the configured duration, you will need to switch to the
OK
pulse menu.
OK
If the same times were configured for several days, these will only occupy one memory slot.
Pulse programs can be saved to 58 memory slots.
h) Manually selecting the switching status
In the menu
1. Press the MENU (2) button three times to switch to the Man menu.
MENU
Alternatively, press the
switch to the next menu. The "Man" symbol will flash on the LCD
display.
Man
2. If several switch channels are available, select the desired channel.
OK
If there are two switch channels, press the ok (9) button to select
+
-
the desired channel. The first channel icon C1 will flash (or C2).
OK
Press the
Confirm your selection with the ok button.
3. Press the - (3) or + (10) buttons to scroll through the settings. If
the
or "Off", this indicates that the relay connection is permanently
switched on or off.
OK
A cycle program switches the current on/off for a preset switch
interval. During this time, cyclic intervals (on/off) are repeated
periodically. The cycle time can be set up to a maximum dura-
tion of 99 minutes and 59 seconds. The
when the time switch is running/switching according to the
cycle program. This program is suitable for slowly flashing
lights or billboards.
1. Press the MENU button (2) to switch to the cycle menu.
Alternatively, press the
+ (10) button, and then press
again to switch to the next menu. The
on the LCD display.
2 Press the - (3) or + (10) buttons to select a new
program setting.
3 Use the - (3) or + (10) buttons to configure the start
time, duration of a switching phase, pause duration and
end time, and confirm your selection with the ok button.
4 To check the configured times, you will need to switch to
the cycle menu.
symbol will flash on the LCD display.
+ (10) button, and then press again to
- (3) or
+ (10) button to select the switch channel.
hand symbol flashes and is displayed together with "On"
4. If the
hand symbol flashes and is displayed together with "On" or "Off", this indicates that the relay
connection is in the opposite switch position for the duration of the current switch interval:
- On, if it was switched off during the switch interval
- Off, if it was switched on during the switch interval.
5. Press the - (3) or + (10) button to select the switch mode. Confirm your selection with the ok button.
If there is a second channel, repeat the process for the second channel.
6. Select the "Auto" option to cancel manual settings and switch according to the normal switch intervals.
symbol will flash
If your time switch has two relay connections, the channel display with the preset switch options
will alternate every 15 seconds.
Shortcut with buttons: changing the switch status until the end of the program
•
You can manually change the switch status of a switch interval. To manually change the status of the
current switch interval, hold down the - (3) and + (10) buttons for approx. 1 second. The first channel
(C1) will be switched.
•
Depending on the current switching state, the switching channel will be switched on or off. If the channel
symbol will flash
is currently switched on, it will be switched off. "On
switched off, it will be switched on. "Off
•
To manually switch the second channel (C2), hold down the + (10) and ok (9) buttons for approx. 1
second. The selected switch status will override the pre-programmed status until the end of the switch
interval.
•
The manually selected switch status will apply until the end of the preset switch interval. For example, if
the programmed switch interval "ON" runs from 11 to 12 o'clock and the status is manually changed to
"OFF" at 11:11, the channel will remain switched off until 12 o'clock. Subsequent programs will switch on
and off according to the preset configurations.
Shortcut with buttons: Setting the switch status to always OFF
•
To switch between always ON (
buttons for 2 seconds.
•
To manually switch the second channel (C2) between "On
(10) and ok (9) buttons for 2 seconds.
•
The manually selected switch status will apply permanently for all switch intervals.
i) Setting a PIN
You can set a PIN to secure your settings. A PIN cannot be deleted once it has been configured.
symbol will
MENU
Man
OK
+
-
OK
OK
+
-
OK
OK
3. If you choose not to configure a PIN, the PIN settings menu will be closed.
4. If you choose to configure a PIN, enter your four-digit PIN using the - (3) or + (10) buttons and confirm
each digit with the ok button.
5. If you have configured a PIN and no buttons are pressed for 60 seconds after starting a setting, the
time switch will be locked. You will then be prompted to enter the PIN in order to unlock the time switch.
If you forget your PIN, it is not possible to configure a new PIN, and you will not be able to use
the time switch.
Care and cleaning
•
Use a dry, lint-free cloth to clean the product.
Disposal
a) Product
Electronic devices are recyclable waste and must not be placed in household waste. At the end
of its service life, dispose of the product according to the relevant statutory regulations. The
built-in battery must be removed by a specialist before disposal.
b) Batteries
You are required by law to return all used batteries (Battery Directive). They must not be placed
in household waste.
Batteries that contain hazardous substances are labelled with this symbol to indicate that dis-
posal in domestic waste is forbidden. The abbreviations for heavy metals in batteries are: Cd =
Cadmium, Hg = Mercury, Pb = Lead (indicated on the battery, e.g. below the waste icon on the
left).
Used batteries can be returned free of charge to local collection points, our stores or battery retailers.
You thus fulfil your statutory obligations and contribute to environmental protection.
" will appear on the LCD display. If the channel is
" will appear on the LCD display.
) and always OFF (
1. Press the MENU (2) button three times to switch to the Man menu.
Alternatively, press the
switch to the next menu. The "Man" symbol will flash on the LCD
display.
2. Press the
- (3) or
mode. Use the - (3) or + (10) buttons to select whether you wish
+
-
to configure a PIN, and then press the ok button to confirm.
OK
), press and hold the - (3) and + (10)
" and "Off
", press and hold the +
+ (10) button, and then press again to
+ (10) buttons to select PIN configuration
Publicité
Table des Matières
