Product Specifications; Technical Data - F.F. Group AG 230/2400S PRO Notice Originale

8 | English

PRODUCT SPECIFICATIONS

INTENDED USE
The machine is intended for cutting, roughing and
brushing of metal and stone materials without the
use of water.

TECHNICAL DATA

Article number
Model
Rated voltage
Rated power input
Rated speed
Grinding disc diameter,
max.
Thread of grinder spindle
Thread length (max.) of
grinder spindle
Weight
Sound emission values determined according to
EN 60745-1
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Uncertainty K
Vibration total values a
and uncertainty K determined according to EN
60745-1
Vibration level max:
a
h,AG
K
NOISE/VIBRATION INFORMATION
The vibration level given in this information sheet
has been measured in accordance with a standard-
ized test given in EN 60745 and may be used to
compare one tool with another. It may be used for
a preliminary assessment of exposure. The declared
vibration emission level represents the main appli-
cations of the tool. However if the tool is used for
different applications, with different accessories or
insertion tools or is poorly maintained, the vibration
emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not
actually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organization of work patterns.
IDENTIFICATION
1. On/Off switch
1a. Safety lock-out
2. Spindle lock button
41631
AG 230/2400S PRO
V 230-240
Hz 50/60
W 2.400
min 6.600
-1
mm 230
M 14
mm 13,5
kg 5,6
dB(A) 95
dB(A) 106
dB
(triax vector sum)
h
m/s 11,862
2
m/s 1,5
2
3. Auxiliary handle
4. Protective guard
5. Release lever for protection guard
6. Spindle
7. Clamping flange
8. Spanner
9. Mounting flange
USE
MOUNTING OF ACCESSORIES (E)
Clean spindle (06) and all parts to be mounted.
h
Tighten clamping flange (07) with spanner (08) while
h
pushing spindle-lock button (02).
For removing accessories handle vice-versa.
h
MOUNTING OF AUXILIARY HANDLE (D)
Screw auxiliary handle (03) on the right, the top, or
the left of the tool (depending on the work to be
carried out).
REMOVING / MOUNTING / ADJUSTING OF PRO-
TECTIVE GUARD (C)
Place protective guard (04) on the spindle collar of the
h
tool head and turn it to the required position (depend-
ing on the work to be carried out).
If necessary, adjust protective guard (04) by tighten-
h
ing screw which is pre-set at manufacturing.
BEFORE USING THE TOOL
Ensure that accessory is correctly mounted and firmly
h
3 tightened.
Check if accessory runs freely by turning it by hand.
h
Test-run tool for at least 60 seconds at highest no-load
h
speed in a safe position.
Stop immediately in case of considerable vibration or
h
other defects and check tool to determine the cause.
SWITCHING ON AND OFF (Β)
Switching on the device:
h
Press the safety lock-out (01a).
ƒ
Then press the ON / OFF switch (01).
ƒ
Switching off the device:
h
Release the ON / OFF switch (01).
ƒ
ROUGH GRINDING
The best roughing results are achieved when setting
h
the machine at an angle of 30° to 40°. Move the ma-
chine back and forth with moderate pressure. In this
manner, the workpiece will not become too hot, does
not discolor and no grooves are formed.
Never use a cutting disc for roughing.
h
CUTTING
Do not tilt the tool while cutting.
h
Always move the tool in same direction as arrow on
h
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner.
Do not apply pressure on the tool; let the speed of the
h
cutting disc do the work.
The working speed of the cutting disc depends on the
h
material to be cut.
Do not brake cutting discs with side pressure.
h
MAINTENANCE
Regular inspection and cleaning reduces the neces-
AG 230/2400S PRO