Automatismos Pujol WINNER PRO V2 400/200 EF Instructions De Montage Et De Service page 10

winner Pro
RULES TO AVOID ACCIDENTS DURING INSTALLATION
The connection of the motor to the power line should be performed only after completion of the installation
described below and only before the operation direction test and check of the limit. The operation direction test and
check of the limit switch should be carried out while maintaining at a safe distance from the crumple zone of the
door.
SPECIFICATIONS FOR INSTALLATION
The motor must be installed in a space provided with protection so that special tools only are needed for assembly.
This protection will prevent contact with the crumple zone of the door itself. The protection would not be necessary if
the installation is done at a height exceeding 2.7 meters. In case of Dead Man functioning, the command position
must be installed near the gate, in a position to allow the direct and complete visualization of the same. In case of
doors with empty elements, you must verify the absence of fixed structures near the door, which can create zones of
crushing. Photocells or sensors will be installed when required by applicable laws. The use of photocells or sensors is
required when you install more than one centralized automated door or in case door is automated in an area that is
not under direct control.
RULES TO AVOID ACCIDENTS DURING THE MAINTENANCE
Maintenance should be performed only after the motor has been prepared in safety mode. This is achieved by
activating the switch pole, making sure it does not turn off during the maintenance operation (lock, signalling, etc.).
NOTE TO THE USER
DESCRIPTION OF THE PRODUCT
CONDITIONS OF USE
The Winner Pro and Winner Pro EF motors are intended for installation of doors winding systems by qualified
personnel. The Winner Pro range motors are designed and constructed for the installation of roller shutters provided
with a compensation system (by springs) according to the weight limits indicated in the table related to the technical
specifications. It is prohibited the use of the motor in applications other than those mentioned above.
WINNER PRO
TECHNICAL DATAS
V3 400/60
Absorbed power
Lifting
Power supply
Current
Nominal torque
Pulley speed
Working temperature
Maximum door travel
Operation time
Weight of the motor
MOUNTING OPERATIONS
Drill in the shutter's central shaft (Fig. 4) one hole Ø 10 mm. in order the operator doesn't turn, and another Ø 12 mm. for
the electric wire. If possible, place the operator in the centre of the shutter's shaft in an easy position for opening the
micro-switches lid to make the wire and the regulation of the limit switches. In case of electric brake, make another drill of
Ø 10 mm. for the cable of the manual release.
Open the pulley unscrewing the M8x25 screws remove the plastic roller band without folding it and keep it in a clean
place. Separate the gear-motor's body removing the 4 screws with the 6mm. (fig. 5). hexagonal wrench.
Couple the two parts of the gear-motor around the door's shaft and joint them screwing the 4 screws on the gear-motor's
support (fig. 6)
Tighten the M10x40 screw (Fig. 8 A) entering it into the Ø 10 mm. hole of the shutter's shaft.
Put again the plastic roller band in its place.
Apply again the pulley by coupling the two parts and tighten the screws.
Screw also the M10x40 (Fig. 8 B), bi-motor (fig. 10 B). Pressing on the shaft till the gear-motor is blocked and tighten the
nut.
The maintenance or testing of the gear is prohibited to unauthorized personnel.
Content (Fig. 1). Tools required (Fig. 2)
WINNER PRO
V3 400/60 EF
400 W
110 Kg. 105 Kg.
1.8 A.
115 Nm.
120 Nm.
5 '
6 Kg. 7 Kg.
WINNER PRO WINNER PRO
V3 600/60 V3 600/60 EF
600 W
150 Kg. 145 Kg.
II 230 V. 50/60 Hz +-7%
2.6 A.
140 Nm. 130 Nm.
10 r.p.m.
-20° C +50° C
6 m.
4.3 '
6.85 Kg. 7.83 Kg.
WINNER PRO WINNER PRO
V3 1200/60 EF
V3 1200/60
1200 W
305 Kg. 300 Kg.
5.6 A.
300 Nm. 295 Nm.
4.3 '
8.36 Kg. 9.36 Kg.
9