FAAC KP 868 SLH Mode D'emploi page 4

ENGLISH
4. Programming
This device has two programming levels: a first level with basic functions and a second one with advanced functions. Procedure for accessing
the menu of each level: combinations of double key strokes, holding down the key until you hear a beep, and input of a programming
Password.
Important:
*
Example :
The following are possible on the first level:
1.A change the PIN (factory value = 1 2 3 4 5 )
1.B transmit the System Code of the 4 channels (only for MASTER)
1.C change the keypad from MASTER to SLAVE ( irreversible setting )
The following are possible on the second level:
2.A change the programming Password (factory value = 1 2 3 4 5 )
2.B delete all codes (restore PIN and Password factory values, randomising system codes).
4.1 Transmission of system code
The teaching of the system code is obviously only possible if the keypad is set as a MASTER (default), otherwise the keypad gives an error
signal (4 consecutive beeps).
To transmit the system code to an SLH type decoding board, to an 868SLH radio control or to another 868SLH Keypad, proceed as follows:
- enter the 1.B menu until a long beep is sounded and hold down the key you require on the keypad;
- hold down the code learning key on the decoding board; or hold down the key of the channel you require on the radio control,
putting it in contact with the keypad; or access the channel you require on the destination keypad (typing in the PIN) and hold
down the key to put the two keypads in contact. Next check if the board's LED stays lighted steady for a few seconds before
going off; or check if the radio control's LED flashes before going off; or check if the destination keypad sounds a long beep
before going off. This is to confirm that the system code was saved.
- release the held down keys.
- to definitively store the keypad's channel on the receiving board, access the channel (typing in the PIN) and press it twice in a row.
4.2 Learning the system code from radio control 868SLH
The system code can also be learned from radio control 868SLH MASTER: put the radio control in teaching mode (refer to the relevant
instructions), press and hold down the key you require. Then access the required channel on the keypad (typing in the PIN) and hold
down the key to put the two units in contact. Check if the keypad sounds a long beep before going off to confirm that the system code
was saved.
The following is a diagram of the programming menus.
Keys
1 + 3
3 beeps
3 beeps
4 + 6
1.A
3 beeps
3 beeps
1.B
1 + 2
3 beeps 3 beeps
1.C
7 + 9
3 beeps
7 + 8
3 beeps
2.A
3 beeps
2.B
until the Password is modified, a PIN must be used to access the different menus. In this
situation, uses a single code (PIN) to access both the radio channels and programming. If
the Password is modified, use the new Password to access programming and continue
using the PIN code to access the radio channels.
PIN = 12345 or XXXXX
Password = 12345
Programming code = PIN
Channel access code = PIN
long beep
input
Programming
*
code
long beep
input
Programming
*
code
long beep
input
Programming
*
code
3 beeps
input
8 + 9
Programming
code
3 beeps
input
2 + 0
Programming
code
PIN = 12345 or XXXXX
Password = YYYYY
Programming code = Password
Channel access code = PIN
2 beeps
input new
PIN (5 digits)
press one of keys 1, 3, A, B
to transmit the System
Code
set as SLAVE
2 beeps
input new
long beep
Password
*
(5 digits)
long beep
deletion
*
performed
4
ENGLISH
long beep
reinput new
output
PIN (5 digits)
LEDS OFF
output
LEDS OFF
output
LEDS OFF
reinput new
long beep
output
Password
LEDS OFF
(5 digits)
output
LEDS OFF