Certifying The Configuration - HOPPECKE sun | powerpack classic 5.5/24 Manuel D'installation Et D'utilisation

Absorption time for equalisation
charging "AptTmEqu"
Cycle for full charging
"CycTmFull"
Cycle for equalisation charging
"CycTmEqu"
Nedap PowerRouter:
Parameter
Battery type
Battery capacity
Shutdown SOC – System for self-
consumption in backup – operation
(mains supply not available)
"Max. shutdown SOC backup"
Shutdown SOC – System for self-
consumption (mains supply available)
"Max. shutdown SOC
self-consumption"
Shutdown SOC – Backup system
(mains supply not available)
"Max. shutdown SOC backup"
Battery charging current
"Max. charging current"
Max. battery discharge current
"MAX_DISCHARGE_CURRENT"
Voltage for equalisation charging
"Equalisation voltage"
Voltage for float charging
Battery float voltage/
"MAINCHG_VCHARGE_BU_AB"
Voltage for float charging
"Float charging voltage"
Cycle for float charging
"Battery maintenance period"
Winter mode
"Battery winter mode"
Battery-Undervoltage Protection
"Discharge-Factor (low current)"
Battery-Undervoltage Protection
"Protection-voltage (low current)"
Battery-Undervoltage Protection
"Discharge-Factor (high current)"
Battery-Undervoltage Protection
"Protection-voltage (high current)"
Battery-Undervoltage Protection "I10" C10 capacity in Ah/
Installation and Operating Manual sun | powerpack
714 080 2000 V1.0 (03.2015)
48
12 hours
14 days
90 days
Value to be set Comments
24 V lead battery
C10 = capacity with discharge
C10 capacity in Ah
over 10 hours
Related to the nominal capacity
60%
C10
Related to the nominal capacity
50%
C10
Related to the nominal capacity
80%
C10
HOPPECKE connectors, cables
Max. current value
and fuse units must be used.
3 x I10
2,40 V/cell
(= 28.8 V for 24 V
battery)
2,50 V/cell
(= 30 V for 24 V
battery)
2,26 V/cell
(= 27.2 V for 24 V
battery)
14 days
Start time:
1st December
End time:
1st February
0.162
24.12 V
4
22.88 V
10 in A
classic
KACO Powador gridsave eco:
Parameter
Battery type
Battery capacity (C10)
Shutdown SOC
Max. charge current
Initial stage current
Bulk stage current
Absorption stage current
Initial stage voltage
Bulk voltage
Absorption stage voltage
Equalise stage voltage
Float stage voltage
Cycle for equalisation charging
"Equalise Period"
DC shutdown (Battery 100% load)

8.2.1 Certifying the configuration

Please certify the configuration of the inverter in accordance with the parameter values mentioned
with your signature. The original of the signed document must remain with the operator of the PV
system and kept in safe custody.
Date ________________________________
____________________________________
Installation/Solar Engineer
An updated listing of the inverter that has been cleared and the parameter values to be adjusted
is given at www.hoppecke.com under the "Downloads" tab.
Installation and Operating Manual sun | powerpack
Value to be set Comments
Sealed
C10 = capacity with
C10 capacity in Ah
discharge over 10 hours
50% Related to the C10 capacity
HOPPECKE connectors,
90 A cables and fuse units
must be used.
HOPPECKE connectors,
90 A cables and fuse units
must be used.
75 A
60 A
2.30 V/cell
(55.2 V for 48 V battery)
2.35 V/cell
(56.4 V for 48 V battery)
2.40 V/cell
(57.6 V for 48 V battery)
2.50 V/cell
(60 V for 48 V battery)
2.25 V/cell
(54.0 V for 48 V battery)
90 days
48.48 V
45.84 V
____________________________________
Operator/End customer
classic
714 080 2000 V1.0 (03.2015)
49