Garmin REACTOR 40 KICKER SUZUKI Instructions D'installation page 3

3
Connect the throttle actuator cable to the carburetor linkage
(Connecting the Throttle Actuator Cable to the Carburetor
Linkage, page 3).
4
Assemble the parts in this adapter kit and secure them to the
motor (Throttle Actuator Component Connections, page
5
Using the Reactor 40 Kicker Throttle Actuator Installation
Instructions , complete and test the throttle actuator
installation.
Assembling the Carburetor Linkage
The carburetor linkage allows the throttle cable from the actuator
to pull open the carburetor throttle lever on the motor.
1
Using the parts provided in this adapter kit, place the
carburetor linkage bracket
carburetor linkage arm
2
Using the bolt and nut provided in this adapter kit, fasten the
bracket to the arm.
3
Tighten the nut so the bracket is securely connected to the
arm, but loose enough so the bracket moves freely.
Connecting the Throttle Actuator Cable to the
Carburetor Linkage
The carburetor linkage is designed to hold the cable from the
throttle actuator securely. Because of the design, you must
connect the throttle actuator cable to the carburetor linkage
before you secure the parts to the motor.
1 If necessary, assemble the carburetor linkage
the Carburetor Linkage, page
2
Place the round end of the throttle actuator cable into the
hole on the end of the carburetor linkage.
3
Rotate the cable so it feeds through the slot on the end of the
linkage.
Throttle Actuator Component Connections
Installation Instructions
on the tapered end of the
.
(Assembling
3).
Part
Throttle actuator
cable (from the
3).
throttle actuator
box)
Throttle cable
bracket
Manifold mounting
location
Carburetor
1
linkage
Securing the Throttle Actuator Cable to the Bracket
Before securing the cable to the bracket, you should connect the
end of the throttle actuator cable to the carburetor linkage
(Connecting the Throttle Actuator Cable to the Carburetor
Linkage, page 3).
1
Place the top of the bracket
throttle actuator cable
2
Secure the cable to the bracket using the included screws
Setting the Linkage Components for Proper Idle
After you install the throttle actuator components on the motor,
you must adjust them so the motor idles correctly.
1 Loosen the throttle actuator bracket on the engine manifold
until the throttle actuator does not pull open the carburetor
throttle lever.
There should be obvious slack in the throttle actuator cable.
2
Adjust the tiller throttle to idle, start the motor, and complete
an action:
• If the motor is not idling correctly, loosen the set screw on
the carburetor throttle lever, adjust the tiller throttle linkage
rod until the motor idles correctly, and tighten the set
screw.
• If the motor idles correctly, proceed to the next step.
3
Using the tiller throttle, increase the speed of the motor, and
complete an action:
• If the motor does not increase its speed and return to idle
correctly, repeat the previous step to adjust the tiller
throttle linkage rod.
1
There is a black rubber pad on the motor manifold that may interfere with the
movement of the carburetor linkage. If the throttle actuator cannot increase the
throttle beyond idle because it contacts the rubber pad, you can trim or smooth the
pad to prevent contact.
Notes
You should connect the throttle actuator cable to
the carburetor linkage before securing it to the
throttle cable bracket (Connecting the Throttle
Actuator Cable to the Carburetor Linkage, page
You must secure the throttle actuator cable
the throttle cable bracket using the included
screws (Securing the Throttle Actuator Cable to
the Bracket, page 3).
You must remove the existing bolt on the manifold
and use it to secure the throttle cable bracket
You must assemble the carburetor linkage before
installing it (Assembling the Carburetor Linkage,
page 3).
The carburetor linkage arm is keyed to fit only one
way on the carburetor.
over the raised portion of the
.
3).
to
.
.
3