Hour Meter - Husqvarna DE 110i Manuel D'utilisation

CAUTION:
battery is installed correctly into the
battery holder. If the battery does not
move easily into the battery holder, the
position is not correct.
2. Remove a blocked battery by pushing through the
access holes. (Fig. 25)
3. Push on the lower part of the battery until you hear a
click. (Fig. 26)
4. Examine the battery lock indicator for correct battery
installation. This only applies for DE 120 PACE. (Fig.
27)
5. Push the battery release buttons (A) and remove
the battery (B) from the battery holder to prevent
accidental start. (Fig. 28)
To start and stop
Note:
The suction is not at full capacity directly at
start, the suction operates fully after 5 seconds.
1. Install the battery. Refer to
battery on page 17 .
2. Push the On/Off button to start the product. (Fig. 29)
3. Select correct hose diameter. Refer to
hose nozzle diameter on page 17 .
4. To stop the product, push and hold the On/Off button
until the green LED light goes off.
5. Remove the battery from the battery holder. Refer to
To install and remove the battery on page 17 .

Hour meter

The hour meter shows the total operation time of the
product in hours.
To remove dust particles from the
prefilter during operation
The filter purge procedure cleans the prefilter from
unwanted material. Do the procedure in these situations:
• Before a work stop or at the end of each work day.
If the product is off for a while, it gives the dust
more time to fall down. This makes the filter purge
procedure more powerful.
• When the suction is not sufficient.
• Before installation of a new Longopac bag.
• When the prefilter clogged alarm goes off. Refer to
the instructions on the decal on the prefilter cover.
1. Start the product. Refer to
18 .
2. Close the air flow that moves through the air intake
with the air intake plug or the intake valve to make
vacuum. (Fig. 30)
18
Make sure that the
To install and remove the
To select the
To start and stop on page
3. Wait 5 seconds until vacuum is made, then push the
filter purge button. Do this step 3 to 5 times. It is
important to let the product make vacuum between
each button push. (Fig. 31)
If the suction is not sufficient after this procedure, it is
necessary to clean the prefilter with water. Refer to
clean the prefilter with water on page 20 .
To install a new Longopac bag cassette
CAUTION:
you install a new Longopac cassette. Refer
To clean the prefilter with water on page
to
20 .
1. Put the Longopac cassette around the inner edge of
the Longopac holder.
2. Remove the 4 straps after you put the Longopac in
the holder.
3. Pull the inner layer of the Longopac cassette up (A)
and fold it into the holder (B). (Fig. 32)
4. Attach the Longopac holder to the rear part of the
container (A). Then attach the Longopac holder to
the sides and to the front of the container (B). Push
the Longopac holder up until you hear a solid click.
(Fig. 33)
5. Make sure that the Longopac is sealed. (Fig. 34)
6. Pull the outer layer of the Longopac cassette down.
(Fig. 35)
7. Close the bottom of the Longopac with a cable tie.
(Fig. 36)
To discard a full Longopac bag and
prepare a new Longopac bag
WARNING:
caution, a full Longopac bag can be heavy.
Make sure that the cable ties are closed
correctly before you lift the Longopac bag.
1. Pull out the Longopac bag (A) and attach a cable tie
(B) to close the new Longopac bag. (Fig. 37)
2. Shake down the dust in the used Longopac bag.
3. Attach a cable tie 10 cm/3.9 in. below the first cable
tie to close the used Longopac bag. Cut off the
Longopac bag between the cable ties. (Fig. 38)
4. If the remaining part of the Longopac bag cassette
is too small to prepare a new Longopac bag, install
a new Longopac bag cassette. Refer to
new Longopac bag cassette on page 18 .
5. Obey local regulations for disposal of the full
Longopac bag.
To
Clean the prefilter before
Lift the Longopac bag with
To install a
1618 - 004 - 24.01.2022