Product Description And Specifications - Bosch PSS 200 A Notice Originale

Masquer les pouces Voir aussi pour PSS 200 A:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 14
certain conditions, for example if flying sparks are cre-
ated when sanding metals. This risk is increased if the
sanding dust is mixed with paint or polyurethane residue
or with other chemical substances and if the workpiece is
hot as a result of prolonged work.
Clean the air vents on your power tool regularly. The
u
motor's fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Always wait until the power tool has come to a com-
u
plete stop before placing it down.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Technical Data
Orbital sanders
Article number
Rated power input
Orbital stroke rate preselection
No-load speed
No-load orbital stroke rate
Orbit diameter
Sanding sheet dimensions
– Hook-and-loop backing
– Clamping tension
Weight according to EPTA Procedure
01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-4.
Bosch Power Tools
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for dry sanding of wood, plastic,
metal, filler and varnished surfaces.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Orbital stroke rate preselection thumbwheel (PSS
250 AE)
(2) On/off switch
(3) Complete dust box (Microfilter system)
(4) Clamps (PSS 200 AC/PSS 250 AE)
(5) Sanding plate
(6) Sanding sheet
(7) Handle (insulated gripping surface)
(8) Extraction outlet
(9) Filter element (Microfilter system)
(10) Dust extraction hose
(11) Punch
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
PSS 200 A
3 603 C40 0..
W
200
rpm
12,000
rpm
24,000
mm
2.0
mm
93 x 185
mm
kg
1.6
/ II
Typically, the A-weighted noise level of the power tool is: 82
dB(A); sound power level 93 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
A)
A)
PSS 200 AC
3 603 C40 1..
3 603 C40 2..
200
12,000
7000–12,000
24,000
14,000–24,000
2.0
93 x 230
1.6
/ II
1 609 92A 49J | (25.07.2018)
English | 11
PSS 250 AE
250
2.0
93 x 185
93 x 230
1.6
/ II

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Pss 200 acPss 250 ae

Table des Matières