Standard Equipment; Set Up And Operation Equipment Setup; Connections; Operation - Ridgid Kollmann SeeSnake KD-200 Consignes De Sécurité

Kollmann
Push Cable Diameter
Mini SeeSnake: .............0.315 in. (.8 cm)
Standard SeeSnake: .....0.43 in. (1.1 cm)
Camera Size & Weight
B&W Mini SeeSnake: ....1.75 x 1 in., 1.5 oz.
(4.4 cm x 2.5 cm, .042 kg)
Color Mini SeeSnake:....2 x 1.26 in., 3.07 oz.
(5.1 cm x 3.2 cm, .087 kg)
B&W SeeSnake:............1.84 x 1.37 in., 2.82 oz
(4.68 cm x 3.48 cm, .08 kg)
Color SeeSnake: ...........2.17 x 1.69 in., 4oz.
(5.5 cm x 4.3 cm, .113 kg)
Depth Rating: ................All cameras waterproof to
330' (100 m)
Camera Resolution
B&W Mini SeeSnake: ....400 HTVL
Color Mini SeeSnake:....330 HTVL
B&W SeeSnake:............400 HTVL
Color SeeSnake: ...........330 HTVL
Lighting
B&W Mini SeeSnake: ....15 Red LED's
Color Mini SeeSnake:....30 White LED's
B&W SeeSnake:............35 Red LED's
Color SeeSnake: ...........45 White LED's
Environmental
Rating: ...........................IPx4
Operating Environment
Temperature..............32° F to 104° F (0°C to 40°C)
Altitude ......................Up to 6560 ft. (2000 m)
Transient
Over voltage ..............Installation Categories II
(1500V Phase to Earth)
Pollution Degree 2

Standard Equipment

• Camera Reel with Push Cable
• Camera Head
• Cable CountIR
• Centering Guides (standard and ball-type)
• C-Rings (for holding Centering Guides onto spring
assembly)
• SeeSnake System Cable
• Universal Spanner Wrench (for Camera Head re-
moval)
• Pair of Plastic Coated Gloves
8
Standard and Mini SeeSnake Diagnostic Equipment
Ridge Tool Company
• SeeSnake Instructional Video
• Operator's Manual
Set Up and Operation
Equipment Setup
1. For Standard SeeSnake reels, install the wheels as
described in appendix A.
2. Place the reel so the push cable is easy to manage
as you push the camera through the line. Three to
five feet from the access point seems to work best.
3. Set up the Camera Control Unit (CCU) so its moni-
tor screen is easy to see and it's controls are easy to
reach during use. In brightly lit areas, point the mon-
itor screen away from bright light sources and/or
use the monitor's sun shade to reduce glare.
4. Adjust the reel's brake so the drum turns easily
when you pull cable from the reel, but stops turning
when you stop pulling the cable; if the drum turns too
easily, excess cable could wind out of the reel.

Connections

1. Plug the Camera Control Unit into an AC outlet and
reset the GFCI if necessary.
2. Unwrap the SeeSnake System Cable from its holder
on the reel frame and plug its connector into the
matching connector on the CCU. To join the con-
nectors, align the guide pin to the guide socket,
push the connector straight in and tighten the outer
locking sleeve. (Figure 6)
NOTE! Twist only the locking sleeve! Never bend or
twist the connector! Bending or twisting the con-
nector will lead to premature failure. When
unplugging you may wiggle a little, if neces-
sary, but do not bend or twist.

Operation

1. Place the camera head into the reel's guide hoop as
shown in Figure 4, and turn the CCU's power ON.
You should see the words "SeeSnake CountIR" and
a version number on the monitor screen. Leave the
camera head in the guide hoop until this start-up
screen disappears (approx. 15 sec.). If you do not
see an image on the monitor, check to make sure its
power is turned on.
2. Put the camera head into the access point and adjust
the camera's lighting with the Dimmer/Transmitter
control.
3. Turn the CountIR's display modes ON or OFF as de-
sired. If you want to measure distance, reset its