Publicité
Les langues disponibles
Les langues disponibles
EN
User Manual
E27 lamp socket with microwave & light sensor
1
Safety Instructions
1.1
General
•
Read the user manual completely and carefully before use.
The user manual is part of the product and contains important
information for correct use.
•
Keep this user manual.
The user manual must be available for uncertainties and passing the
product.
Risk of electric shock
•
Do not open the housing.
•
Do not modify product and accessories.
•
Do not short connectors and circuits.
•
Use product, product parts and accessories only in perfect
condition.
A defective device may not be put into operation, but must be discon-
nected from mains and protected against further use.
•
In case of questions, defects, mechanical damage, trouble and
other problems, non-recoverable by the documentation, contact
your dealer or producer.
Target group information
Not meant for children.
•
Secure packaging, small parts and insulation against acciden tal
use.
•
Handle the product carefully.
It will be damaged by blows, knocks or a fall from even a short height.
•
Avoid stresses such as heat and cold, moisture and direct sunlight
vibration and mechanical pressure.
•
Do not immerse the product in liquids and protect it from splashing
water.
1.2 Warning levels
Warnings against hazards that may result in injuries in case of
nonobservance.
Warnings against hazards that may result in material damage
in case of non-observance.
2
Description and Function
2.1
Product
This product is an energy saving switch for ceiling lighting. The product is equipped
with a microwave motion sensor that responds to human motion. With adjustable
switch-off delay and adjustable detection distance of the microwave sensor. Ideal for
storerooms, attics, cellars, garages, hallways and stairwells. Works through doors,
glass, thin walls and furniture.
2.2
Scope of delivery
E27 lamp socket with microwave & light sensor, user manual
2.3
Operating elements and product parts
Fig. 3: Operating elements
1 Lamp socket
3 "SENSOR" control
2.4
Specifications
Article Number
Operating voltage
Max. power per lamp socket:
Bulb
LED / Energy-saving lamp
Microwave sensor
Detection radius
Detection distance
Frequency range
Operating illuminance
Switch-off delay
Operating temperature range
Socket design
Socket material
Protection class / protection level
Dimensions (L x Ø)
Weight
Tab. 2: Specifications
REV2018-03-28
V1.0
2 "TIME" control
4 Light sensor
55501
220-240 @ 50 Hz
V~
60
W
20
W
360
°
3-7
m
2,8
GHz
≤ 3
Lux
15 - 300
s
0 ~ 35
°C
E27
Copper, PBT
II / IP20
108,34 x 65,80
mm
89,5
g
3
Intended Use
We do not permit using the device in other ways like described in chapter
Description and Function. Use the product only in dry interior rooms. Not
attending to these regulations and safety instructions might cause fatal
accidents, injuries, and damages to persons and property.
4
Connecting
Material damage
The wireless lamp socket is designed for a maximum switching capaci-
ty of 60W.
•
Do not overload the socket with lamps that are too strong!.
See also chapter 2.4 "Specifications".
•
Installieren Sie die Lampenfassung in einer Höhe von 2 ~ 3,5 m.
If the specified height is undershot or exceeded, there is a restric
tion of the function of the sensors and switching on their lighting is not possible.
•
Make sure that the lamp holder is not mounted in the detection
range of another light source, otherwise the built-in light sensor
prevents the light from being switched
1.
Compare the specifications of all used devices to ensure compati-
bility
2.
Check the scope of delivery for completeness and integrity.
3.
Set the desired lighting duration (after microwave sensor detected
movement and switched-on the light) using the "TIME" control (2).
For testing, we recommend a setting to the minimum value = 15 sec.
4.
Set the desired detection range of the microwave sensor via the
"SENSOR" control (3).
For testing it is recommended to adjust the maximum value = 7 m.
Max.
300 Sec.
+
TIME
Fig. 4: Testeinstellungen
5.
Turn off the lamp you want to equip with the lamp socket.
6.
Screw the lamp socket directly into the socket of the lamp.
7.
Screw the desired light source into the lamp socket.
8.
Turn on the light again.
The light will turn on as soon as it is dark enough and the microwave
sensor registers a movement within the preset triggering range.
5
Maintenance, Care, Storage and Transport
The products are maintenance-free.
Material damage
•
Clean only with a dry, soft cloth.
•
Do not use cleaning agents and chemicals.
•
Store cool and dry.
•
Store the product out the reach of children and in a dry and
dust-protected ambience when not in use.
•
Keep and use the original packaging for transport.
6
Liability Notice
•
We reserve the right to printing errors and changes to product,
packaging or product documentation.
•
See our terms of warranty. These are available in their cur-
rent form under the given contact details.
7
Disposal Notes
According to the European WEEE directive, electrical and elect-
ronic equipment must not be disposed with consumers waste.
Its components must be recycled or disposed apart from each
other. Otherwise contaminative and hazardous substances can
pollute our environment.
As a consumer, you are committed by law to dispose electrical
and electronic devices to the producer, the dealer, or public
collecting points at the end of the devices lifetime for free. Parti-
culars are regulated in national right. The symbol on the product,
in the user`s manual, or at the packaging alludes to these terms.
With this kind of waste separation, application, and waste dispo-
sal of used devices you achieve an important share to environ
mental protection.
WEEE No: 82898622
- 2 -
on.
Min.
Max.
Min.
15 Sec.
7 m
3 m
-
+
-
SENSOR
by Wentronic GmbH | Pillmannstraße 12
38112 Braunschweig | Germany
55501
Goobay
®
Publicité
