Triple Element Activation; Bridge Element Activation; Fast Boil (Booster) Function; Switching An Element Off - Blomberg CTE 30400 Manuel D'utilisation

Switching off a cooking zone as described below
disables the Low Power mode. When the zone will be
selected again it will start to work in the standard power
mode.
6ZLWFKLQJ DQ HOHPHQW RII
7RXFK WKH UHODWHG >2))@ NH\ UHI LQ RUGHU WR VWRS D
heating element.
You may turn off all active elements at the same time by
WRXFKLQJ WKH PDLQ >212))@ NH\
'XDO HOHPHQW DFWLYDWLRQ
6HOHFW D GRXEOH KHDWLQJ DUHD WRXFKLQJ WKH UHODWHG >21@
NH\ WKH +27 685)$&( OHG UHI EHJLQV WR ÀDVK
7RXFK WKH >'28%/(@ NH\ LQ RUGHU WR HQDEOHGLVDEOH WKH
outer ring of a double zone. This operation is possible
ZKLOH WKH +27 685)$&( OHG UHI LV ÀDVKLQJ
The dual element enabling indication (ref.5a) is on
when the element is enabled, is off when the element
is disabled.
7ULSOH HOHPHQW DFWLYDWLRQ
6HOHFW D PXOWLSOH KHDWLQJ DUHD WRXFKLQJ WKH UHODWHG >21@
NH\ WKH +27 685)$&( OHG UHI EHJLQV WR ÀDVK
7RXFK WKH >75,3/(@ NH\ LQ RUGHU WR HQDEOHGLVDEOH WKH
outer rings of a triple zone:
‡ ,I RQO\ WKH LQQHU HOHPHQW LV HQDEOHG WKH LQWHUPHGLDWH
ring is enabled too.
‡ ,I WKH LQQHU DQG WKH LQWHUPHGLDWH HOHPHQWV DUH
enabled, the outer ring is enabled too.
‡ ,I DOO WKH HOHPHQWV DUH HQDEOHG WKH RXWHU DQG WKH
intermediate rings are disabled.
These operations are possible until the HOT SURFACE
OHG UHI LV VWLOO ÀDVKLQJ
The intermediate element enabling indication (ref.5a) is
on when the double element is enabled, is off when the
double element is disabled.
The outer element enabling indication (ref.5b) is on
when the triple element is enabled, is off when the triple
element is disabled.
%ULGJH HOHPHQW DFWLYDWLRQ
Select one of the two single heating areas belonging
WR WKH EULGJH WRXFKLQJ WKH UHODWHG >21@ NH\ WKH +27
685)$&( OHG UHI EHJLQV WR ÀDVK
7RXFK WKH >%5,'*(@ NH\ LQ RUGHU WR HQDEOH WKH EULGJH
element and set the whole cooking area as a single
unit.
This operation is possible until the HOT SURFACE led
UHI LV VWLOO ÀDVKLQJ EHIRUH RU DIWHU VHWWLQJ WKH SRZHU
level:
‡ 6HW WKH SRZHU OHYHO RQ WKH VHOHFWHG ]RQH WKHQ WRXFK
WKH >%5,'*(@ NH\ ERWK WKH GLVSOD\V ZLOO VKRZ WKH
same power level and both extension lights (ref.1a,
1b) turns on.
‡ 7RXFK WKH >%5,'*(@ NH\ ERWK +27 685)$&(
OHG UHI EHJLQ WR ÀDVK DQG ERWK H[WHQVLRQ OLJKWV
(ref.6a, 6b) turns on. Set the power level that will be
immediately and simultaneously displayed on both
displays.
6b
6a
Figure. 9
2QFH WKH EULGJH FRQ¿JXUDWLRQ LV DFWLYH WKH >21@ DQG
>2))@ NH\V RI WKH WZR VLQJOH ]RQHV LQYROYHG FDQ EH
used indifferently to control the bridge area. All actions
will have the same effect on the whole cooking area.
7KH EULGJH FRQ¿JXUDWLRQ FDQQRW EH GLVDEOHG ZKLOH LV
active. It's always necessary to switch the area off: the
bridge will be disabled automatically.
+RW VXUIDFH LQGLFDWRU OLJKW
Each element has a HOT SURFACE indicator light
(ref.3) to show when the cooking area is hot.
This indication turns on when the zone is activated and
remains ON until the cooking area has cooled down to
D ³VDIH WR WRXFK´ WHPSHUDWXUH DSSUR[LPDWHO\ ƒ) 
If a hot surface light is ON use caution when working
around the cooktop as it is still hot.
)DVW %RLO %RRVWHU IXQFWLRQ
Once a heating element has been selected, touch the
>)$67 %2,/@ NH\ WR HQDEOHGLVDEOH WKLV IXQFWLRQ EHIRUH
or after setting the power level.
A beep sounds and the heater display shows the
selected power level and a "P" alternatively.
Use & Care Manual
ENGLISH
3
3
11