Publicité
Les langues disponibles
Les langues disponibles
PREPARATION
"
Build solid framing to the dimensions in Figure 1.
"
Ensure that the floor is level, correct if necessary.
"
The drain location on the tub shower is shown but
actual installation
which is purchased.
"
Drain pipe must be vertical.
"
Trim drain pipe as required to meet drain assembly.
"
Place the unit into position and plumb vertical, shim if
necessary.
"
Dry fit drain to check position.
"
Mark and drill 3/16" pilot holes for plumbing fixtures.
"
Verify that the holes are in the right location.
"
From the finished side of the unit use the correct size
hole saw to cut the openings, using the pilot holes as
guides.
INSTALLATION
"
Carefully position the Tub Shower into the framing
and push flush against the framework walls.
"
Install the drain according to the manufacturer's
instructions. Use a mildew resistant silicone
bathroom caulking to seal the drain to the top surface
of the tub.
"
Marked by dimple holes along the flanges drill 3/16"
hole on each dimple, 7 on each side flanges and 2
across the top flange. Refer to Figure 3.
"
Fasten the acrylic unit to the framing using drywall
screws. Note that over tightening or burying the head
of the screw will cause the acrylic to crack. Please
note to make sure that the unit is plumbed before
fastening.
"
Apply silicone caulking over the head of the screws
and around the openings for the fittings when they
are installed.
TROUBLESHOOTING
"
Excessive gaps at the seams in the back corners:
Shim front post of lower section as illustrated in
Figure 3B.
"
Tub bottom section is not level: Refer to shimming
section on page 1.
"
Water remains around the bathrim or drain: Check
that the installation is level and that the tub sits firmly
on its base; use wood shim to correct.
FINISHING
"
Apply trim around the tub shower periphery to finish
drywall, if required.
"
Install the tub shower door according to the
manufacturer's instructions if purchased.
We want you to be completely satisfied with our products and service. If you have any comments or suggestions, please call 1-800-
will depend on waste/overflow
The company reserves the right to change models and specifications without notice.
60 Shorncliffe Rd., Toronto, Ontario M8Z 5K1
Telephone: (416) 231-9030 - Fax: (416) 231-0929
www.mirolin.com
INSTALLATION CLEAN-UP
Remove construction dirt and residue with a mild liquid
detergent. DO NOT USE abrasive cleaners, scouring
compounds and pads, metal scrapers, steel wool, or other
materials that could damage or dull the surface of the bath.
Remove plaster carefully with a blunt wooden block
having rounded edges.
Remove paint and other stubborn stains with isopropyl
(rubbing) alcohol.
DO NOT USE products such as acetone (nail polish
remover), dry cleaning solution, lacquer thinners,
gasoline, pine oil, etc.
TESTING
Test the installation after completing the plumbing, but
before enclosing the bath and finishing the surroundings.
Fill the bath with water and leave it for one hour to ensure
that the adjustment of the drain-overflow assembly is
correct, and that there are no leaks.
Mirolin Industries Corp. is not responsible for any
damages incurred as a result of poor installation of the
product.
MAINTENANCE
The acrylic sheet, which forms the surface of your bathtub,
provides one of the most durable surfaces found in
modern bathrooms. Keep it bright and smooth with mild
liquid household detergent, soap and water, or foaming
cleansers. NEVER USE aromatic solvents, abrasive
cleaners, scouring compounds or pads, strong liquid
cleansers, or other material that could damage or dull the
surface of the bath.
Restoring Surface Gloss.- Restore surface gloss by
applying a very fine rubbing compound and polishing the
surface by hand or with a power buffer. Finish with an
application of a good quality automotive wax.
Minor Repairs to Surface.- Remove minor scratches and
scuffs as follows. First, wet sand the area with 600 grit wet
sandpaper until the surface is smooth. Then, restore the
gloss as described under RESTORING SURFACE
GLOSS.
MIROLIN toll free.
Customer Service: (416) 231-5790
Canada, U.S.A.: 1-800 - MIROLIN (647-6546)
Fax, Canada: 1- 800 - 463 - 2236
C
US
84 314
11 Apr. 17
3
Publicité
