Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Setting the time for a tanning or relax session
1
Set the time of the tanning or relax session by pushing the + button to put the time forward or by pushing the - button to put the time
backward (fig. 19).
Keep the button pressed to adjust the time more quickly.
2
Lie down directly under the lamp units of the appliance to ensure that the sides of your body are also tanned properly.
3
Put on the protective goggles provided.
Switch on the tanning lamps or the infrared lamps by pressing the start button ∞ (fig. 20).
4
Note: during start-up the tanning lamps may produce a humming sound.This sound will stop as soon as the lamps are burning properly.
B
Note: the tanning lamps will start to emit a visibly stronger light after approx. 60 seconds, which means they are now burning at full power. From this
B
moment onwards you can switch the facial tanner on or off.
Note: if the lamps fail to go on after about 20 seconds, switch the appliance off (∞), let the lamps cool down for 3 minutes, set the tanning time and
B
switch the appliance back on again (∞).
A blinking signal will appear; the set time is shown on the display (25 minutes in this case) (fig. 21).
The countdown of the set tanning or relax session time will now start.
You can switch the facial tanner (•, ª) on or off during the session without having to switch off the whole appliance. (This also holds for the
extra face tan in combination with º) (fig. 22).
The chosen symbols stay visible in the display, but the other symbols do not.
During the last minute of the session you will hear a beeping sound (fig. 23).
During this minute, you can press the pause/repeat button § to repeat the set time (fig. 24).
The display shows the set time and starts to count down.The beeping stops.
It is also possible to set a new time.
By doing this, you can avoid the 3-minute waiting time which is necessary to allow the tanning lamps to cool down after they have been
switched off.
This waiting time does not apply to the infrared lamps (type HB975 only).
Set a new time by pushing the ¢ and £ buttons.Then push the start button ∞ (fig. 25).
5
The beeping stops and the time that has just been set starts counting down.
When you do not repeat the time or set a new time during the last minute of the session, the countdown continues and the appliance will
automatically switch off as soon as the set time has passed.
Interrupting the tanning or relax session
You can interrupt the tanning session by pushing the pause/repeat § button (fig. 26).
1
The lamps will be switched off, ¶ appears on the display together with the remaining time.The remaining time will blink for 3 minutes. During
this time the lamps cool down.When the blinking has stopped, you can switch the appliance back on again by pushing the ∞ button.The
remaining time will now be counted down.
You can interrupt the relax session by pushing the pause/repeat § button.
2
The lamps will be switched off, ¶ appears on the display together with the remaining time (not blinking).You can switch the appliance
immediately back on again by pushing the ∞ button.The waiting time does not apply in the case of the infrared lamps.The remaining time will be
counted down.
Changing the tanning or relax time during a session.
1
When you are tanning, you can change the set time by pushing the ∞ button.The lamps will be switched off.Then set a new time by
pushing the ¢ and £ buttons.Wait until the set time has stopped blinking (this will take 3 minutes because the lamps have to cool down
first) and push the ∞ button again.
When relaxing (l), you can change the set time by pushing the ∞ button.The lamps will be switched off.You can set a new time and switch
the appliance back on immediately by pushing the ∞ button.The waiting time does not apply in case of the infrared lamps (the newly set
time does not blink on the display).
Make sure the right lamps are switched on:
(HB975, HB971) Tanning: 4 lamps (one in every lamp unit) or 1 lamp (in the side lamp unit).The lamps emit a bluish light (fig. 27).
(HB975 only) Relaxing: 2 lamps (one in every side lamp unit).The lamps emit red light (fig. 28).
Cooling
The appliance is cooled by means of fans to prevent materials and parts from becoming too hot.The tanning lamps won't go on if they are too
hot (see for instance 'Interrupting the tanning or relax session').
After you have switched off the tanning lamps or infrared lamps, the fans will continue to work for three more minutes.
This is convenient, because it enables you to use the tanning lamps again only 3 minutes after switching them off (the infrared lamps do not
require a cooling-down period before they can be switched on again!)
B
If you have switched the tanning appliance off by removing the plug from the wall socket, the fans won't provide cooling for three more minutes, of
course.Therefore, if another person wishes to use the appliance for a tanning session right away, this person must first allow the tanning appliance to
cool down.
HB975 only: If you want to use the appliance for a tanning session immediately after having used it for a relax session (l), you should also let the
B
appliance cool down for three minutes. As a result of the relax session, the tanning lamps will have become hot and will need to cool down before
they can be switched on.
Cleaning
1
Always unplug the appliance and let it cool down before you start cleaning it.
2
Clean the outside of the appliance with a damp cloth.
ENGLISH
7
Publicité
Table des Matières
