Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Labormat TH
11. Operating the Labormat TH
11.1 Filling with water
Open the lid of the device (4) and
remove the flask baskets (optional)
and support plate (55). The rear wall of
the water tank features an angle mark.
This indicates the maximum permissi-
ble water level.
Important: Never fill the device
above this mark. Overfilling can
cause leaks in the pump system
which in turn causes water to be
discharged.
There are two ways of filling the device:
1. Manual filling
Use a suitable vessel (e. g. bucket) or
water hose to fill the requisite water
volume (approx. 15 litres) directly into
the heating basin through the opening
in the device.
11.2 Establishing operational readiness
1. Press the red main switch (14) in the
control panel (7) to activate the power
supply. The pilot light integrated in the
switch lights up indicating operational
readiness of the device.
2. Set the rotary knob (19) on the ther-
mostat (22) to the requisite water tem-
perature. Important: The Labormat
TH pump does not work until an
operating temperature of 65 °C has
been reached. This reliably prevents
wax deposits in the pump housing and
spray system thereby preventing func-
56
2. Fixed connection
A water supply hose (
D1017E)
available as an option connects the
Labormat TH directly with the water
line (shut-off valve required). Unscrew
the seal nut at the back of the device
and firmly connect the supply hose with
the lock nut on the water inlet (top left
on rear of device). Connect the other
end of the connection hose to the water
line directly via a shut-off valve. Open
the shut-off valve and fill in water as
far as the maximum level. Replace the
support plate (55) and flask baskets
(accessories, please refer to page 31)
in the device and close the lid (4).
tional faults. When the pre-set tem-
perature is reached, the yellow pilot
light (17) in the control panel stays on.
It takes approx. 20 minutes to heat the
water to 65 °C.
It takes approx. 40 minutes to heat the
water to 95 °C.
11.3 Boiling out
Raise the double lid (4) at the handle
The Labormat TH avails of a double
(53) and fold backwards. Place the
lid. For brief boiling out using the hand
items to be boiled out on the support
spray (30), only raise the sealing cover
plate (55) or in the flask baskets avail-
at the handle (53) and fold backwards.
able as an option. Close the lid (4) and
Place the item to be cleaned (e. g. artic-
activate the timer (19/20) in the control
ulator) on the perforated metal lid and
panel (7). The spray function can be
remove the hand spray (30) from the
pre-selected variably between 0 and 6
holder (10).
minutes. As an alternative to the timer
Set the timer (19/20) to the specified
(19/20), the green hold button (15) in
cleaning time or press the hold button (15)
the control panel can also be pressed to
while pressing the pressure switch on
automatically trigger the spray process
the hand spray.
which is maintained for as long as the
The white pilot light (16) lights up in
hold button is pressed.
the control panel during the active
spray process.
Important: The timers on the
Labormat device should not be
Important: Spray tubes, flask bas-
turned anticlockwise mechani-
kets and all other internal metal
cally. This over-stresses the inter-
surfaces display high temperatures
nal parts and can expose the clocks
during and after use. They should
to fast wear.
not be touched – even briefly – with-
out using the designated handles.
11.4 Polymerising
thermostat (24) and boil-dry protec-
Labormat devices are also suitable for
tion (21), and must not be removed
polymerising hot-polymerising resins
or displaced except when subjecting
using metal the flask technology. Do
the device to overall cleaning. Various
this by opening the double lid (4) and
temperature levels can also be realised
removing the flask baskets (optional)
via the thermostat controller (19/22)
and support plate (55) (Caution: Risk
to ensure homogeneous plastic poly-
of burning – only touch using the
merisation. During the polymerisation
designated handles) and submerge
process, the Labormat can also be used
the flasks directly in the preheated
as a boil-out unit; replace the support
water tank. The base of the water tank
plate (55) and flask baskets (optional)
features a perforated metal cover (6)
in the device and proceed as outlined
which protects the heating element (28)
in the section on „Boiling out".
underneath and the sensors for the
57
Publicité
Table des Matières
