Sera LED Digital Dimmer 31070 Mode D'emploi page 7

US
Information for use
sera LED Digital Dimmer
Please read these instructions carefully and keep for future use. When forwarding this unit to third parties, this in-
formation for use is also to be handed over.
Congratulations!
Congratulations for buying the LED Digital Dimmer. The sera
LED Digital Dimmer is a controller for programming sera
LED lighting appliances such as the sera LED X-Change
Tubes, sera LED aquariums and the sera LED lights. You
can adjust maximum brightness and use the dimmer as a
time clock. Combination with the sera LED X-Change
sunrise Tubes and some of the sera LED Chips even al-
lows simulating sunrise and sunset in combination with
2 different cloud scenarios and midday dimming as desired.
In case of the sera LED X-Change cool daylight Tubes and
other sera LED products, dimming does not alter the light
color but only changes the brightness. Cloud simulation by
the sera LED Digital Dimmer is possible with all LED tubes.
SAFETY PRECAUTION
Use the sera LED Digital Dimmer only as described in this
information for use. It is a low voltage dimmer for a range of
10 – 20 V DC. The maximum current on the input side should
not exceed 3 A. Maximum input voltage cannot exceed the
output voltage.
Application
The brightness of the lamps connected to the Digital
Dimmer increases or decreases in pre-programmed steps.
Adjustment can be done either automatically or manually.
Application range
The sera LED Digital Dimmer can be used in a ver satile
way and allows controlling the sera LED X-Chan ge Tubes
as well as the sera LED aquariums and sera LED lights.
sera LED X-Change System
The sera LED Digital Dimmer allows operating one or more
sera LED X-Change Tubes (also different lengths) up to a
total of 60 W.
sera LED aquariums
All sera LED aquariums such as the marin Biotop LED Cube
130, the Biotop LED Cube 130 XXL, the Biotop Nano LED
Cube 60 and the Biotop Nano LED Cube 16 can be operat-
ed and programmed with the sera LED Digital Dimmer.
sera LED lamps
The sera Nano LED light and the sera LED light, both
equipped with sera LED Chips, can be connected solely or
combined with more units by the sera LED Triple Cable,
and can be programmed with a single sera LED Digital
Dimmer.
When connecting several lamps/units of the same voltage
(for example do not combine 12 V and 20 V lamps, but only
12 V and 12 V or 20 V and 20 V), it is necessary to choose a
suitable electronic bal last. Make sure the output voltages of
the ballast and the operating ranges of the LED lamps are
identi cal. For instance, never connect a 12 V LED lamp to a
20 V ballast! Warranty of the devices will be void in case of
damage as consequence of inappropriate use!
When the sera LED Digital Dimmer is used with other LED
lamps or illuminating light units, make sure that the maxi-
mum current flow is not exceeded, and that the lamps are
really dimmable in the range of 10 – 20 V. Several LED lamps
can be connected to one ballast.
Kit includes (1)
1.1 sera LED Digital Dimmer with cable and
5.5 mm barrel connectors
1.1.1 display
1.1.2 HOUR, F1 – F7, DEMO key
1.1.3 MINUTE, ON/OFF, RESET key
1.1.4 MINUS key
1.1.5 PLUS key
1.1.6 SET key
1.2 holder
1.3 screws (4 pieces)
Assembly instruction
The sera LED Digital Dimmer should be connected be-
tween ballast and LED lamp. Should you intend to control
more than one light unit, please connect the sera LED
Triple Cable to the outlet connector of the dimmer. By add-
ing more triple cables you can even attach more applianc-
es. The barrel connectors of the cables do not allow confu-
sion, and polarity reversion cannot occur.
Location
The sera LED Digital Dimmer should be installed
in an easily accessible and dry place. Use the hold-
er for installing the dimmer into the cabinet or where
you prefer. The holder (1.2) can be attached with
4 screws (1.3).
Operation
ON/OFF
Press "MINUTE" to switch the light ON/OFF.
7