Service Information; Warranty; Full Two-Year Home Use Warranty; Troubleshooting - Black & Decker SMARTSELECT BDPH400 Mode D'emploi

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable
power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the
Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under
"Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com
WARNING:
Tool service must be performed only by qualified repair personnel.
WARNING:
When servicing a tool, use only identical replacement parts.

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The
defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased
(provided that the store is a participating retailer). Returns should be made within the time period of the retailerʼs policy
for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer
for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for
repair or replacement at our option. Proof of purchase may be required.Black & Decker owned and authorized Service
Centers are listed under "Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other
rights which vary from state to state or province to province. Should you have any questions, contact the manager of
your nearest Black & Decker Service Center. This product is not intended for commercial use.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America,
check country specific warranty information contained in the packaging, call the local company or see the website for
warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call
1-800-544-6986 for a free replacement.
Problem
• Material runs or drips
• Too much over spray.
• Little or no material being released.
• Material being sprayed is splattering.
• Sprayer pulsates.
• Liquid comes out side of canister.
• Cannot depress trigger to start
spraying.
For assistance with your product, visit our website www.blackanddecker.com for the location of the
service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.

SERVICE INFORMATION

WARRANTY

TROUBLESHOOTING

Possible Cause
• Spraying too much material.
• Spraying too slowly.
• Spraying too close.
• Viscosity too thin.
• Sprayer too far from surface.
• Too much material being sprayed. • Reduce air flow by turning flow control
• Check valve ball stuck.
• Spray nozzle/tip clogged.
• Pickup tube loose or clogged.
• Air hose split or disconnected.
• Flow control knob setting too low.
• Air inlet blocked.
• Material too thick.
• Viscosity of material is too high.
• Air filter clogged.
• Material in canister almost empty.
• Lid not on square or tight enough. • Remove lid and reattach squarely and
• Paint on threads of canister
and lid.
• Flow control setting is set
completely to the minimum side.
11
Possible Solution
• Reduce air flow by turning flow control
knob.
• Increase speed of application.
• Increase distance from surface.
• Check dilution recommendation.
• Reduce distance to surface.
knob.
• Remove check valve. Depress ball to
loosen. Add lubricant. See figure Q.
• Clean nozzles.
• Check tube.
• Check air hose.
• Increase flow control setting.
• Clean or change air filter.
• Check viscosity recommendation.
• Thin material per manufacturer
recommendation.
• Clean or change filter.
• Refill canister.
evenly, then tighten lid securely.
• Clean threads on top and sides of
canister and lid.
• Back the flow control knob off
(clockwise) to allow for more trigger travel.
See 'Tools-Elec-
tric'
– Yellow Pages –
for Service &
Sales