VONROC CR503DC Traduction De La Notice Originale page 12

EN
Setting the Automatic Shut­Off Pressure (Fig. E)
1. Press the pressure selector (21) on the controle
panel to switch between the different pressu-
re Units ( PSI, BAR, Kpa) until required unit is
displayed.
2. Press the "+"or "-" on the controle panel until
the desired pressure shows on the display. By
holding the "+"or "-" you can go up or down
quicker, release "+"or "-"at the dissured pressu-
re.
Note: After 3 seconds the display will flash and
return to a reading of "0.0". This is normal. The set
pressure will be remembered.
3. Move the mode selector I/0/II (20) into the
position 'I' to switch the appliance to start the
High pressure.
4. When the item to be inflated has reached the
preset valuepressure the unit will automatically
turn off.
Note: You may notice the actual pressure reading
may drop after a couple of seconds. This is normal.
5. To stop the inflator at any time, move the mode
selector I/0/II (20) into the position 'O' to switch
the appliance off.
Note: If the power switch is turned off, all settings
will be lost and will need to be reentered. This is
a safety feature to prevent the risk of items OVER
INFLATING.
Note: After a few minutes the machine automati-
cally goes off. In order to switch on the machine,
press the Pressure selector (21) and the display
(28) will go on.
Note: When using the Dunlop valve adapter, the
pressure gauge will not display an accurate value
due to characteristics of the valve. When inflating
a tire, do not use the value on the pressure gauge,
but inflate it by checking the status of the tire. If
the tool stops before the tire reaches the desired
air pressure, adjust the pressure value, and then
inflate the tire again.
Note: When inflating a floating tube, the pressure
gauge will not display an accurate value since
the pressure of floating tube is less than 20 kPa
12
(3 PSI). When inflating a floating tube, do not use
the value on the pressure gauge, but inflate it by
checking the status of the floating tube.
Using the Inflator as a Pressure Gauge
Note: This machine has a memory mode in pre-set
function.
Please make sure to switch machine off to remove
memory before using pressure gauge function.
1. In order to switch on the machine, press the Pres-
sure selector (21) and the display (28) will go on.
2. Reattach the hose connected to the valve to be
measured.
3. The digital readout will display the item's pressu-
re.
Removing the connection valve (Fig. D1, D2)
• Removing with or without valve adapter: Open
the clamping lever (7) for the connection valve
(8) and remove from the valve and/or adapter of
the inflatable.
• Remove any adapter and close the valve of the
inflated item (ball, inflatables or tyres)
Note: Air may escape from the valve of the infla-
table when removing the connection valve (8). Be
sure not to remove the connection valve (8) too
quickly. It may be necessary to add extra pressure
to the required pressure, to compensate for the
escaped air.
Storage high pressure hose and valve adapters
(Fig. F, G)
• The high-pressure hose (9) is located in a storage
channel (10) on the back of the machine. Wrap
the high-pressure hose inside the channel.
• The Valve adapters (14, 15, 16) are stored in the
back of the unit inside the valve adapter storage
(19).
OW PRESSURE, HIGH VOLUME - INFLATA-
BLES - SWITCH 'II'
Inflating
Connecting the low pressure hose to the compressor
(Fig. H1)
1. Remove the low pressure hose (11) from the
storage (12).
2. Line up the notches (24) of the hose with the
nubs (23) of the low pressure inflator connection
(22) .
WWW.VONROC.COM