Additional Safety Rules - Makita HR2440 Manuel D'instructions

ENGLISH
1 Grip base
2 Side grip (auxiliary handle)
3 Teeth
4 Protrusions
5 Loosen
6 Tighten
7 Bit shank
8 Bit grease
SPECIFICATIONS
Model
Capacities
Concrete
Tungsten-carbide tipped bit................ 24mm
Core bit .............................................. 54mm
Diamond core bit (dry type) ............... 65mm
Wood .................................................... 32 mm
Steel ..................................................... 13 mm
-1
No load speed (min ).............................. 0 – 1,100
Blows per minute ..................................... 0 – 4,500
Overall length .......................................... 352 mm
Net weight................................................ 2.3 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for hammer drilling and drilling in
brick, concrete and stone. It is also suitable for drilling
without impact in wood, metal, ceramic and plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold tools by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Wear ear protectors when using the tool for
extended periods. Prolonged exposure to high
intensity noise can cause hearing loss.
Explanation of general view
9 Bit
10 Chuck cover
11 Depth gauge
12 Switch trigger
13 Lock button
14 Lamp (HR2440F only)
15 Reversing switch lever
16 Action mode changing knob
HR2440/HR2440X/HR2440F
3.
4.
5.
6.
7.
8.
9.
10. Do not leave the tool running. Operate the tool
ENB010-1
11. Do not point the tool at any one in the area when
12. Do not touch the bit or parts close to the bit
SAVE THESE INSTRUCTIONS.
17 Blow-out bulb
18 Dust cup
19 Chuck adapter
20 Keyless drill chuck
21 Sleeve
22 Ring
23 Tighten
24 Loosen
HR2441
24mm
54mm
65mm
32 mm
13 mm
0 – 1,100
0 – 4,500
352 mm
2.3 kg
Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, and thickly
padded gloves.
Be sure the bit is secured in place before opera-
tion.
Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
Hold the tool firmly with both hands.
Keep hands away from moving parts.
only when hand-held.
operating. The bit could fly out and injure some-
one seriously.
immediately after operation; they may be
extremely hot and could burn your skin.
HR2442
24mm
54mm
65mm
32 mm
13 mm
1,100
4,500
352 mm
2.3 kg
5